Re: USB CNC (was Interface. Gauging interest.)
Posted by
Wayne C. Gramlich
on 2006-05-20 00:00:48 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett <KM6VV@...> wrote:
<http://gramlich.net/projects/cnc/axis4/index.html>
You were probably looking at the previous release:
<http://gramlich.net/projects/cnc/motion/rev_d/index.html>
The previous release tried to the micro-step chopping
using an A/D converter tied to the current sense
resistor. It didn't work worth a darn!!! I had quite
a bit of help from this list educating as to the folly
of using a slow A/D converter to do the micro-step
chopping.
web site:
<http://www.microchip.com>
and type "USB" into the search bar on the main page.
If you look through the resulting search results,
you'll find their example USB driver code labeled
as "Firmware Drivers". The code is written in
Hi-TEC C.
Bringing up a UART looks to be about 100 times easier
than bringing up a USB connection in terms of the
amount of code required. That is why I ultimately
dumped USB support; it looked like a major project
that could distract me for many many months.
[snip]
Enjoy,
-Wayne
>The latest one is at:
> Hi Wayne,
>
> An old version you say? Thought I was looking at the
> newest one!
<http://gramlich.net/projects/cnc/axis4/index.html>
You were probably looking at the previous release:
<http://gramlich.net/projects/cnc/motion/rev_d/index.html>
The previous release tried to the micro-step chopping
using an A/D converter tied to the current sense
resistor. It didn't work worth a darn!!! I had quite
a bit of help from this list educating as to the folly
of using a slow A/D converter to do the micro-step
chopping.
> So then you aren't using the USB. Too bad. I was hopingIf you want to read some USB code, go to the Microchip
> to get a peek at some USB code for the PIC.
web site:
<http://www.microchip.com>
and type "USB" into the search bar on the main page.
If you look through the resulting search results,
you'll find their example USB driver code labeled
as "Firmware Drivers". The code is written in
Hi-TEC C.
Bringing up a UART looks to be about 100 times easier
than bringing up a USB connection in terms of the
amount of code required. That is why I ultimately
dumped USB support; it looked like a major project
that could distract me for many many months.
[snip]
Enjoy,
-Wayne
Discussion Thread
Dennis Schmitz
2006-05-12 00:26:44 UTC
Interface. Gauging interest.
ballendo
2006-05-12 02:33:46 UTC
Re: Interface. Gauging interest.
lcdpublishing
2006-05-12 04:34:40 UTC
Re: Interface. Gauging interest.
Fred Smith
2006-05-13 09:29:18 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-13 17:57:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
turbulatordude
2006-05-13 18:34:05 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-15 10:03:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-15 10:31:40 UTC
Re: Interface. Gauging interest.
Jack Hudler
2006-05-15 10:57:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-15 11:21:49 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-15 12:23:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Roy J. Tellason
2006-05-15 12:58:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-15 13:09:24 UTC
Re: Interface. Gauging interest.
Mike Pogue
2006-05-15 13:39:03 UTC
USB-to-step/direction (was Interface. Gauging interest.)
Codesuidae
2006-05-15 13:51:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-15 14:41:53 UTC
Re: Interface. Gauging interest.
Jack Hudler
2006-05-15 14:47:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike
2006-05-15 14:53:37 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-15 14:54:07 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-15 15:07:28 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-15 15:08:32 UTC
Re: Interface. Gauging interest.
Roy J. Tellason
2006-05-15 15:24:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Roy J. Tellason
2006-05-15 15:28:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
lcdpublishing
2006-05-15 16:25:26 UTC
Re: Interface. Gauging interest.
Graham Stabler
2006-05-15 17:26:42 UTC
Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-15 17:36:42 UTC
Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-15 18:10:03 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-15 18:32:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Codesuidae
2006-05-15 18:37:07 UTC
Re: [CAD_CAM_EDM_DRO] USB-to-step/direction (was Interface. Gauging interest.)
ballendo
2006-05-15 20:35:11 UTC
Re: Interface. Gauging interest.
Jack Hudler
2006-05-15 21:38:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
JanRwl@A...
2006-05-15 22:07:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike Pogue
2006-05-15 22:11:15 UTC
Re: [CAD_CAM_EDM_DRO] USB-to-step/direction (was Interface. Gauging interest.)
JanRwl@A...
2006-05-15 22:19:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-15 22:24:36 UTC
Re: Interface. Gauging interest.
Tony Jeffree
2006-05-15 22:32:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dave Halliday
2006-05-15 23:01:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike Pogue
2006-05-16 00:08:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike Pogue
2006-05-16 00:13:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Jack Hudler
2006-05-16 00:17:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike Pogue
2006-05-16 00:18:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Lester Caine
2006-05-16 00:24:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Jack Hudler
2006-05-16 00:30:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-16 01:08:35 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 01:16:52 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 01:19:38 UTC
OT Re: Interface. Gauging interest.
ballendo
2006-05-16 01:25:07 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 01:32:25 UTC
Re: Interface. Gauging interest.
Graham Stabler
2006-05-16 02:07:21 UTC
Re: Interface. Gauging interest.
Lester Caine
2006-05-16 04:23:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
lcdpublishing
2006-05-16 06:03:14 UTC
Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 07:49:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Roy J. Tellason
2006-05-16 08:04:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 08:23:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-16 09:11:32 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-16 09:14:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Codesuidae
2006-05-16 09:23:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
gort38
2006-05-16 09:36:00 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 09:42:33 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 09:49:07 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 09:55:54 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-16 10:03:37 UTC
Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 10:05:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 10:19:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-16 10:39:14 UTC
Re: Interface. Gauging interest.
Dan Mauch
2006-05-16 11:05:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
gort38
2006-05-16 11:32:18 UTC
Re: Interface. Gauging interest.
Dave Halliday
2006-05-16 11:32:57 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike Pogue
2006-05-16 11:51:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
wanliker@a...
2006-05-16 12:18:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Codesuidae
2006-05-16 12:35:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 12:36:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Lester Caine
2006-05-16 12:46:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 12:53:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-16 13:03:38 UTC
OT Re: Interface. Gauging interest.
wanliker@a...
2006-05-16 13:05:51 UTC
Interface. Gauging interest.
Codesuidae
2006-05-16 14:41:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-16 14:43:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Phil Mattison
2006-05-16 15:23:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Codesuidae
2006-05-16 15:40:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-16 15:53:31 UTC
Re: Interface. Gauging interest.
Steve Blackmore
2006-05-16 17:22:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Phil Mattison
2006-05-16 17:29:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-16 18:47:10 UTC
Re: Interface. Gauging interest.
Jon Elson
2006-05-16 21:44:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Lester Caine
2006-05-16 22:42:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Steve Blackmore
2006-05-17 00:05:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
lcdpublishing
2006-05-17 05:32:10 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-17 07:06:18 UTC
Re: Interface. Gauging interest.
Phil Mattison
2006-05-17 08:51:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Roy J. Tellason
2006-05-17 08:55:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
lcdpublishing
2006-05-17 09:22:57 UTC
Re: Interface. Gauging interest.
Phil Mattison
2006-05-17 09:47:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-17 09:58:14 UTC
Irrelevant Gcode?!? wasRe: Interface. Gauging interest.
ballendo
2006-05-17 10:00:45 UTC
irrelevnat Gcodes was Re: Interface. Gauging interest.
ballendo
2006-05-17 10:02:38 UTC
Re: Interface. Gauging interest.
lcdpublishing
2006-05-17 10:13:56 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-17 10:17:41 UTC
Re: Interface. Gauging interest.
Fred Smith
2006-05-17 11:13:43 UTC
Re: Interface. Gauging interest.
Lester Caine
2006-05-17 11:40:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-17 11:57:03 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-17 20:30:08 UTC
Re: Interface. Gauging interest.
Jack Hudler
2006-05-17 21:04:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Jack Hudler
2006-05-17 21:04:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-17 22:01:51 UTC
Re: Irrelevant Gcode?!? wasRe: Interface. Gauging interest.
lcdpublishing
2006-05-18 04:58:52 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-18 05:11:22 UTC
OT Re: Interface. Gauging interest.
Graham Stabler
2006-05-18 05:29:38 UTC
OT Re: Interface. Gauging interest.
Steve Blackmore
2006-05-18 16:31:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
yracg
2006-05-18 20:53:29 UTC
Re: Interface. Gauging interest.
JanRwl@A...
2006-05-18 21:53:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-18 23:18:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mike Pogue
2006-05-19 00:51:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
yracg
2006-05-19 05:49:15 UTC
Re: Interface. Gauging interest.
Peter Reilley
2006-05-19 05:59:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
yracg
2006-05-19 06:22:16 UTC
Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-19 06:58:38 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-19 07:24:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-19 07:26:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-19 07:28:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Phil Mattison
2006-05-19 07:49:51 UTC
[CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Mariss Freimanis
2006-05-19 08:29:00 UTC
Re: Interface. Gauging interest.
yracg
2006-05-19 08:31:36 UTC
Re: Interface. Gauging interest.
Wayne Weedon
2006-05-19 08:40:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Wayne C. Gramlich
2006-05-19 08:51:48 UTC
Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-19 08:55:11 UTC
Re: Interface. Gauging interest.
wanliker@a...
2006-05-19 09:11:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Lester Caine
2006-05-19 09:37:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-19 09:41:18 UTC
Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-19 09:47:00 UTC
Re: Interface. Gauging interest.
Codesuidae
2006-05-19 09:48:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Dennis Schmitz
2006-05-19 09:53:38 UTC
Re: Interface. Gauging interest.
John Dammeyer
2006-05-19 09:54:19 UTC
USB CNC (was Interface. Gauging interest.)
Jack Hudler
2006-05-19 09:57:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-19 10:40:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-19 10:56:20 UTC
RE: [CAD_CAM_EDM_DRO] USB CNC (was Interface. Gauging interest.)
John Dammeyer
2006-05-19 11:23:37 UTC
RE: [CAD_CAM_EDM_DRO] USB CNC (was Interface. Gauging interest.)
Mike Pogue
2006-05-19 11:59:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Lester Caine
2006-05-19 12:05:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-19 12:07:56 UTC
RE: [CAD_CAM_EDM_DRO] USB CNC (was Interface. Gauging interest.)
Mariss Freimanis
2006-05-19 12:27:31 UTC
Re: USB CNC (was Interface. Gauging interest.)
Alan Marconett
2006-05-19 12:48:01 UTC
RE: USB DLP2232M CNC, Was Re: Interface. Gauging interest.
Alan Marconett
2006-05-19 12:56:08 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Wayne C. Gramlich
2006-05-19 13:33:20 UTC
Re: Interface. Gauging interest.
Wayne C. Gramlich
2006-05-19 13:36:36 UTC
Re: Interface. Gauging interest.
Wayne C. Gramlich
2006-05-19 14:00:01 UTC
Re: USB CNC (was Interface. Gauging interest.)
ballendo
2006-05-19 14:06:06 UTC
Re: Interface. Gauging interest.
Alan Marconett
2006-05-19 14:16:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
lcdpublishing
2006-05-19 14:28:40 UTC
Re: PCI interface was ....Interface. Gauging interest.
Alan Marconett
2006-05-19 14:42:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
delmar williams
2006-05-19 14:45:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
Lester Caine
2006-05-19 15:06:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
Wayne C. Gramlich
2006-05-19 15:34:56 UTC
Re: USB CNC (was Interface. Gauging interest.)
Codesuidae
2006-05-19 15:48:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Wayne Weedon
2006-05-19 15:54:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
John Dammeyer
2006-05-19 17:13:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
Paul Kelly
2006-05-19 17:19:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
Mike Pogue
2006-05-19 17:54:12 UTC
Re: [CAD_CAM_EDM_DRO] RE: USB DLP2232M CNC, Was Re: Interface. Gauging interest.
Alan Marconett
2006-05-19 17:59:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
Anders Wallin
2006-05-19 21:49:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
Wayne C. Gramlich
2006-05-20 00:00:48 UTC
Re: USB CNC (was Interface. Gauging interest.)
bob_kellock
2006-05-20 03:18:22 UTC
Re: Interface. Gauging interest.
Les Newell
2006-05-20 05:06:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
Alan Marconett
2006-05-20 10:59:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
Wayne C. Gramlich
2006-05-20 11:58:09 UTC
Re: USB CNC (was Interface. Gauging interest.)
Mariss Freimanis
2006-05-20 13:37:35 UTC
Re: USB CNC (was Interface. Gauging interest.)
Alan Marconett
2006-05-20 14:14:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
Hugh Prescott
2006-05-20 15:13:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
Graham Stabler
2006-05-20 15:57:23 UTC
Re: USB CNC (was Interface. Gauging interest.)
Alan Marconett
2006-05-20 16:00:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC
Dennis Schmitz
2006-05-20 16:48:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ronginger@a...
2006-05-20 17:53:16 UTC
Re: USB CNC (was Interface. Gauging interest.)
Jack Hudler
2006-05-20 19:23:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: PCI interface was ....Interface. Gauging interest.
Jack Hudler
2006-05-20 19:28:08 UTC
RE: [CAD_CAM_EDM_DRO] Re: Interface. Gauging interest.
ballendo
2006-05-20 22:05:57 UTC
Re: Interface. Gauging interest.
ballendo
2006-05-20 22:26:51 UTC
Re: USB CNC (was Interface. Gauging interest.)
Mike Pogue
2006-05-21 01:49:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
Alan Marconett
2006-05-21 10:26:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: USB CNC (was Interface. Gauging interest.)
Alan Marconett
2006-05-21 16:54:05 UTC
Re: [CAD_CAM_EDM_DRO] RE: USB DLP2232M CNC, Was Re: Interface. Gauging interest.
Mariss Freimanis
2006-06-06 19:39:41 UTC
Re: Interface. Gauging interest.
Fred Smith
2006-06-06 20:44:50 UTC
ncPOD update, was Re: Interface. Gauging interest.
John Stevenson
2006-06-06 22:55:16 UTC
ncPOD update, was Re: Interface. Gauging interest.
Tony Jeffree
2006-06-07 00:20:00 UTC
Re: [CAD_CAM_EDM_DRO] ncPOD update, was Re: Interface. Gauging interest.
Tony Jeffree
2006-06-07 00:30:33 UTC
Re: [CAD_CAM_EDM_DRO] ncPOD update, was Re: Interface. Gauging interest.
turbulatordude
2006-06-07 08:34:04 UTC
ncPOD update,
Fred Smith
2006-06-07 11:00:14 UTC
Re: ncPOD update,
Tony Jeffree
2006-06-07 13:19:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: ncPOD update,