Re: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
Posted by
BRIAN FOLEY
on 2006-06-08 09:39:58 UTC
usually the connection is made inside the motor housing and usually easy to
bring out as 4 wires. as for treadmill motors they are made 120 volt or 240
volt for the overseas market. cul brian f.
bring out as 4 wires. as for treadmill motors they are made 120 volt or 240
volt for the overseas market. cul brian f.
----- Original Message -----
From: "turbulatordude" <dave_mucha@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, June 08, 2006 12:06 PM
Subject: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "BRIAN FOLEY" <ka1bbg@...> wrote:
> >
> > Hi, most treadmill motors are permanant magnet at least the ones i have
> > seen. looking at the speed control books i have here, universal
> motors have
> > two types, shunt wound and wound field. one runs on 1/2 voltage for the
> > field the other full voltage for the field. if the two sets of
> winding wires
> > a pair for field and a pair of wires for the armeture are brought to
> a speed
> > control, control should be easy.
>
> Assuming the newer router did not have an on-board speed controller,
> and assuming it was a simple 2 wire plug, would both field and
> armature wires be brought out to the plug ? or would there be some
> other circuitry inside ?
>
> I'm thinking of the capacitor start motors (yes, I know these are not
> cap start) where there is a little extra inside the motor that does
> other functions than just let the motor see wall power all the time.
>
> Dave
>
>
>
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.8.3/358 - Release Date: 6/7/06
>
>
Discussion Thread
turbulatordude
2006-06-02 17:51:33 UTC
Roland CAMM-3 ?
Christian Grunewald
2006-06-02 21:02:34 UTC
RE: [CAD_CAM_EDM_DRO] Roland CAMM-3 ?
BRIAN FOLEY
2006-06-02 21:05:39 UTC
Re: [CAD_CAM_EDM_DRO] Roland CAMM-3 ?
turbulatordude
2006-06-02 23:13:57 UTC
Re: Roland CAMM-3 ?
ballendo
2006-06-03 05:49:23 UTC
Re: Roland CAMM-3 ?
Christian Grunewald
2006-06-03 15:06:08 UTC
RE: [CAD_CAM_EDM_DRO] Re: Roland CAMM-3 ?
turbulatordude
2006-06-03 21:03:54 UTC
Re: Roland CAMM-3 ?
Les Newell
2006-06-04 01:52:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Roland CAMM-3 ?
turbulatordude
2006-06-04 07:45:44 UTC
Re: Roland CAMM-3 ?
Les Newell
2006-06-04 08:00:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Roland CAMM-3 ?
Fred Smith
2006-06-04 11:20:23 UTC
Re: Roland CAMM-3 ?
Mic Arthur
2006-06-05 07:29:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Roland CAMM-3 ?
turbulatordude
2006-06-05 07:55:42 UTC
Re: Roland CAMM-3 ?
lanebarr@b...
2006-06-06 10:49:20 UTC
Re:Re: Roland CAMM-3 ?
Alan Marconett
2006-06-06 11:11:21 UTC
SPINDLE speed controller, collets, WAS re: Roland CAMM-3 ?
Mic Arthur
2006-06-06 11:23:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Roland CAMM-3 ?
turbulatordude
2006-06-06 13:13:02 UTC
Re:Re: Roland CAMM-3 ?
Les Newell
2006-06-07 01:33:15 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE speed controller, collets, WAS re: Roland CAMM-3 ?
turbulatordude
2006-06-07 07:50:42 UTC
Re: SPINDLE speed controller, collets, WAS re: Roland CAMM-3 ?
Alan Marconett
2006-06-07 08:29:27 UTC
RE: [CAD_CAM_EDM_DRO] SPINDLE speed controller, collets, WAS re: Roland CAMM-3 ?
Alan Marconett
2006-06-07 08:49:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets, WAS re: Roland CAMM-3 ?
turbulatordude
2006-06-07 10:12:28 UTC
Re: SPINDLE speed controller, collets, WAS re: Roland CAMM-3 ?
Alan Marconett
2006-06-07 11:52:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
turbulatordude
2006-06-07 13:56:18 UTC
Re: SPINDLE speed controller, collets
Alan Marconett
2006-06-07 15:11:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
BRIAN FOLEY
2006-06-08 02:47:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
Alan Marconett
2006-06-08 08:22:05 UTC
RE: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
turbulatordude
2006-06-08 09:08:43 UTC
Re: SPINDLE speed controller, collets
BRIAN FOLEY
2006-06-08 09:39:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
Alan Marconett
2006-06-08 09:43:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: SPINDLE speed controller, collets
turbulatordude
2006-06-08 12:16:28 UTC
Re:Re: Roland CAMM-3 ? - Lane ?