CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry

Posted by Ron Thompson
on 2010-12-16 16:52:14 UTC
I went the other way. I started by making everything extrusions on top
of extrusions.
I like profiles when I may need different lengths of something. Making
configurations with different lengths is pretty easy.
One of the strengths of Solidworks is the ease of changes, especially if
your original design is made with future changes in mind.
In coming from Autocad, I had a hard time realizing how easy it was to
rough sketch and then add dimensions. Changing them is just as easy.
The other thing I love about Solidworks is on the fly calculations. In
Autocad, I always had a calculator at hand. In Solidworks, I just input
as an equation, like 14-12.7 to get 1.3
SW is also smart enough to do conversions on the fly. If I am making a
model in inches, I can input 17mm and it will convert it. Same with
fractions. Input 5 5/8 and it converts to 5.625.

No, I don't work for Solidworks.<GRIN>

--


Ron Thompson
On the Beautiful Florida Space Coast, right beside the Kennedy Space Center, USA

There are two kinds of posts on newsgroups.
1. This is what I have done...
2. This is what I think...
Be aware of the difference!

http://www.ourcadguy.com/

http://www.plansandprojects.com My hobby pages are here:
http://www.plansandprojects.com/My%20Machines/

Visit the castinghobby FAQ:
http://castinghobbyfaq.bareboogerhost.com/







On 12/16/2010 7:28 PM, timgoldstein wrote:
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com
> <mailto:CAD_CAM_EDM_DRO%40yahoogroups.com>, Ron Thompson
> <barebooger@...> wrote:
> >
> > Good to know. I started to explain my methodology, but wanted to wait
> > until some others did theirs, so as not to contaminate the test.
> >
> > I opened a sketch on the right plain. Starting at to origin (0,0,0), I
> > rough sketched the profile (T shape).
>
> Ron,
>
> Been pondering when I started to move from using profiles to more
> working form primitives. I think the techniques that I had to learn to
> make primitive my preferred approach was getting the hang of sketch
> planes and drafts on extrusions.
>
> Previously when I wanted a dovetail I would always do a profile. But
> then I was shown how to put a draft angle on an extrusion and that
> made something like the dovetail cut on the bottom of a Sherline X
> table into just a rectangle cut extrusion into the table with a draft
> angle on it. Much easier than a profile.
>
> Sketch planes came in when I needed to learn how to put a radial hole
> on a cylinder. Then it became angled sketch planes and splits.
>
> Tim Goldstein
> A2Z Corp
> A2Z CNC division
> 3955 S Mariposa St
> Englewood CO 80110
> 720 833-9300
> Toll Free 877 754-7465
>
> www.A2ZCorp.us/store
> USA made accessories for desktop mills & lathes.
> Specialized tools for the jewelry industry.
>
>


[Non-text portions of this message have been removed]

Discussion Thread

timgoldstein 2010-12-12 22:14:31 UTC CAD experiment idea Roland Jollivet 2010-12-13 03:34:22 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment idea Jamie Cunningham 2010-12-13 03:56:18 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment idea Ron Thompson 2010-12-13 05:24:40 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment idea Tim Goldstein 2010-12-13 05:42:10 UTC Re: CAD experiment idea Ron Thompson 2010-12-13 06:09:06 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment idea Kevin Martin 2010-12-13 07:04:00 UTC RE: [CAD_CAM_EDM_DRO] CAD experiment idea Stephen Wille Padnos 2010-12-13 07:06:33 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment idea Roland Jollivet 2010-12-13 07:46:25 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment idea R.L. Wurdack 2010-12-13 07:54:59 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment idea Tim Goldstein 2010-12-13 08:17:23 UTC Re: CAD experiment idea Tim Goldstein 2010-12-13 08:53:42 UTC Re: CAD experiment idea Tim Goldstein 2010-12-13 09:00:17 UTC Re: CAD experiment idea Tim Goldstein 2010-12-13 09:02:56 UTC Re: Re: [CAD_CAM_EDM_DRO] CAD experiment idea Roland Jollivet 2010-12-13 09:06:29 UTC [CAD_CAM_EDM_DRO] CAD experiment idea timgoldstein 2010-12-13 09:17:38 UTC Re: CAD experiment idea Ron Thompson 2010-12-13 12:45:45 UTC CAD experiment entry timgoldstein 2010-12-13 12:49:59 UTC Re: CAD experiment entry Ron Thompson 2010-12-13 13:29:56 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry H & J Johnson 2010-12-13 15:16:30 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-13 15:34:13 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-13 15:39:54 UTC Re: CAD experiment entry Ron Thompson 2010-12-13 16:00:40 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry H & J Johnson 2010-12-13 16:02:54 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry H & J Johnson 2010-12-13 16:06:50 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-13 16:25:27 UTC Re: CAD experiment entry Michael Fagan 2010-12-13 17:05:04 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment entry Andy Wander 2010-12-13 17:11:24 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry R.L. Wurdack 2010-12-13 17:24:09 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry H & J Johnson 2010-12-13 17:29:58 UTC Re: RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Andy Wander 2010-12-13 18:17:03 UTC RE: RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Peter Homann 2010-12-13 18:48:08 UTC RE: RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Andy Wander 2010-12-13 18:50:57 UTC RE: RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-13 23:23:56 UTC [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-14 05:00:00 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-14 05:17:36 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-14 05:43:39 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment entry Ron Thompson 2010-12-14 05:57:27 UTC Re: [CAD_CAM_EDM_DRO] CAD experiment entry timgoldstein 2010-12-14 08:44:40 UTC Re: CAD experiment entry timgoldstein 2010-12-14 09:25:58 UTC Re: CAD experiment entry H & J Johnson 2010-12-14 09:27:58 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-14 10:12:05 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-14 12:45:23 UTC Re: CAD experiment entry Ron Thompson 2010-12-14 13:39:41 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-14 15:08:47 UTC Re: CAD experiment entry Peter Reilley 2010-12-14 15:25:51 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-14 16:57:56 UTC Re: CAD experiment entry Brian Worth 2010-12-14 21:49:49 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Peter Homann 2010-12-14 22:03:54 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-14 22:46:21 UTC Re: CAD experiment entry William Thomas 2010-12-15 04:27:56 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-15 04:40:51 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Kevin Martin 2010-12-15 05:20:51 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-15 06:23:27 UTC Re: CAD experiment entry timgoldstein 2010-12-15 06:33:51 UTC Re: CAD experiment entry Mike Payson 2010-12-15 06:54:41 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-15 07:00:39 UTC Re: CAD experiment entry Kevin Martin 2010-12-15 07:38:42 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Swiss 2010-12-15 08:26:31 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry CNC 6-axis Designs 2010-12-15 08:29:06 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Jon Elson 2010-12-15 10:45:31 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-15 17:05:59 UTC Re: CAD experiment entry Kevin Martin 2010-12-15 20:24:24 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-15 21:16:03 UTC Re: CAD experiment entry timgoldstein 2010-12-15 21:17:14 UTC Re: CAD experiment entry timgoldstein 2010-12-16 08:37:58 UTC Re: CAD experiment entry Ron Thompson 2010-12-16 09:07:45 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Jon Elson 2010-12-16 10:08:36 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-16 14:34:40 UTC Re: CAD experiment entry timgoldstein 2010-12-16 15:17:46 UTC Re: CAD experiment entry timgoldstein 2010-12-16 16:28:39 UTC Re: CAD experiment entry Ron Thompson 2010-12-16 16:52:14 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry Ron Thompson 2010-12-16 16:57:49 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-16 20:45:14 UTC Re: CAD experiment entry William Thomas 2010-12-16 21:23:48 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD experiment entry timgoldstein 2010-12-16 22:13:34 UTC EMC, Was Re: CAD experiment entry Stephen Wille Padnos 2010-12-17 05:28:36 UTC Re: [CAD_CAM_EDM_DRO] EMC, Was Re: CAD experiment entry Jon Elson 2010-12-17 09:24:52 UTC Re: [CAD_CAM_EDM_DRO] EMC, Was Re: CAD experiment entry Jon Elson 2010-12-17 09:31:09 UTC Re: [CAD_CAM_EDM_DRO] EMC, Was Re: CAD experiment entry Jon Elson 2010-12-17 10:06:09 UTC Re: [CAD_CAM_EDM_DRO] EMC, Was Re: CAD experiment entry Jeffrey T. Birt 2010-12-17 10:28:06 UTC RE: [CAD_CAM_EDM_DRO] EMC, Was Re: CAD experiment entry samcoinc2001 2010-12-17 11:05:31 UTC EMC, Was Re: CAD experiment entry Jon Elson 2010-12-17 19:57:50 UTC Re: [CAD_CAM_EDM_DRO] EMC, Was Re: CAD experiment entry