Re: [CAD_CAM_EDM_DRO] emc
Posted by
Keith Bowers
on 2002-07-17 11:16:04 UTC
Disconnect the hard drive(s) and strip the motherboard down to minimum. If
the machine boots, then start adding things back.
the machine boots, then start adding things back.
----- Original Message -----
From: "Brian Pitt" <bfp@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, July 17, 2002 1:41 PM
Subject: Re: [CAD_CAM_EDM_DRO] emc
> well you could try calling MS support <evil grin>
>
> Brian
>
> > will someone tell me how to get it to boot from a DOS disk so I can
install
> > a good ol' MS OS? It WILL NOT boot from a floppy no matter how I set the
> > bios for which drive to read first.
> >
> snip<
Discussion Thread
batwings@x...
1999-10-10 21:39:43 UTC
emc
TheDragonPit
1999-10-11 08:03:15 UTC
Re: emc
Terry L. Ridder
1999-10-11 08:15:31 UTC
Re: emc
Steve Carlisle
1999-10-11 09:47:45 UTC
Re: emc
Darrell Gehlsen
1999-10-11 09:54:32 UTC
Re: emc
Carlos Guillermo
1999-10-11 11:26:20 UTC
RE: emc
Carlos Guillermo
1999-10-11 11:39:59 UTC
RE: emc
Carlos Guillermo
1999-10-11 11:44:23 UTC
RE: emc
Paul Corner
1999-10-11 12:39:37 UTC
Re: emc
Terry L. Ridder
1999-10-11 12:41:40 UTC
Re: emc
Terry L. Ridder
1999-10-11 13:05:07 UTC
RE: emc
Steve Carlisle
1999-10-11 14:27:59 UTC
Re: emc
Steve Carlisle
1999-10-11 14:30:47 UTC
Re: emc
Jon Elson
1999-10-11 13:48:46 UTC
Re: emc
Matt Shaver
1999-10-11 15:57:50 UTC
Re: emc
Ian Wright
1999-10-11 12:29:06 UTC
Re: emc
Carlos Guillermo
1999-10-12 04:19:28 UTC
RE: emc
batwings@x...
1999-10-11 20:53:46 UTC
Re: emc
batwings@x...
1999-10-11 10:04:00 UTC
Re: emc
Darrell Gehlsen
1999-10-12 10:15:37 UTC
Re: emc
Roger Brower
1999-10-13 13:51:58 UTC
emc
Les Watts
2002-07-17 06:24:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc
Ian W. Wright
2002-07-17 06:56:24 UTC
Re: [CAD_CAM_EDM_DRO] emc
bjammin@i...
2002-07-17 08:02:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc
bjammin@i...
2002-07-17 08:03:41 UTC
Re: [CAD_CAM_EDM_DRO] emc
William Scalione
2002-07-17 09:20:11 UTC
Re: [CAD_CAM_EDM_DRO] emc
Keith Bowers
2002-07-17 11:16:04 UTC
Re: [CAD_CAM_EDM_DRO] emc
Ray Henry
2002-07-17 12:40:06 UTC
Re: Re: Re: emc
Keith Rumley
2002-07-17 14:30:42 UTC
Re: [CAD_CAM_EDM_DRO] emc
dakota8833
2002-07-17 15:05:13 UTC
Re: emc
Marshall Pharoah
2002-07-17 19:30:31 UTC
RE: [CAD_CAM_EDM_DRO] emc
Carol & Jerry Jankura
2002-07-17 20:17:09 UTC
RE: [CAD_CAM_EDM_DRO] emc
Les Newell
2002-07-17 23:59:54 UTC
Re: [CAD_CAM_EDM_DRO] emc
Ray Henry
2002-07-18 06:46:26 UTC
Re: Re: emc
Joll503@A...
2002-07-19 02:20:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc
Jon Elson
2002-07-19 09:11:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc
bjammin@i...
2002-07-22 06:59:02 UTC
Re: [CAD_CAM_EDM_DRO] emc
bjammin@i...
2002-07-25 06:59:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Re: emc
bjammin@i...
2002-07-25 06:59:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc
edward c heil
2003-06-11 16:21:50 UTC
emc
Jon Elson
2003-06-11 21:40:21 UTC
Re: [CAD_CAM_EDM_DRO] emc