Re: gecko's and voltage
Posted by
Lee Studley
on 2003-07-05 13:44:48 UTC
Hi Eric,
I'd go conservative depending on the size of your machine. If you let
a table coast or drop, the servo will generate and pump up the supply
voltage somewhat. I like to give 10-15v as a saftely margin,
otherwise, you could try to make an energy-dump circuit to keep the
supply from pumping up. The drive's mosfets have a Safe Operating Area
(SOAin the datasheets, and as the voltage goes up over 80v many
mosfets will drop-off greatly in the current they will handle.
Check the files sections for eneregy dump circuit. Mariss put a good
one there.
-Lee
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "cnchomeman"
<cnchomeman@y...> wrote:
I'd go conservative depending on the size of your machine. If you let
a table coast or drop, the servo will generate and pump up the supply
voltage somewhat. I like to give 10-15v as a saftely margin,
otherwise, you could try to make an energy-dump circuit to keep the
supply from pumping up. The drive's mosfets have a Safe Operating Area
(SOAin the datasheets, and as the voltage goes up over 80v many
mosfets will drop-off greatly in the current they will handle.
Check the files sections for eneregy dump circuit. Mariss put a good
one there.
-Lee
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "cnchomeman"
<cnchomeman@y...> wrote:
> I bought some gecko320's. My powersupply (transformer/bridge/cap)max.
> measures 80.8 volts no load. This is a whole .8 volts over the
> Anyone have any comments on this? I am currently running on 65volts
> (my transformer has a few taps). I would like to try the 80.8volts,
> but am new to gecko's and don't want to let the smoke out.
>
> Eric
Discussion Thread
cnchomeman
2003-07-05 13:36:51 UTC
gecko's and voltage
Kim Lux
2003-07-05 13:43:38 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
Lee Studley
2003-07-05 13:44:48 UTC
Re: gecko's and voltage
Lee Studley
2003-07-05 13:56:08 UTC
Re: gecko's and voltage
Andrew Mawson
2003-07-05 14:03:31 UTC
Re: gecko's and voltage
Kim Lux
2003-07-05 14:04:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Lee Studley
2003-07-05 14:20:21 UTC
Re: gecko's and voltage
Chris Baugher
2003-07-05 14:34:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
JanRwl@A...
2003-07-05 14:50:47 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
Kim Lux
2003-07-05 14:59:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Kim Lux
2003-07-05 15:03:29 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
Mariss Freimanis
2003-07-05 16:40:31 UTC
Re: gecko's and voltage
Chris Baugher
2003-07-05 17:53:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Jon Elson
2003-07-05 18:41:21 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
Jon Elson
2003-07-05 18:45:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Jon Elson
2003-07-05 18:51:12 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
turbulatordude
2003-07-05 20:28:58 UTC
Re: gecko's and voltage
Tim Goldstein
2003-07-05 20:38:59 UTC
RE: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Tim Goldstein
2003-07-05 20:45:05 UTC
RE: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
JanRwl@A...
2003-07-05 20:47:29 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
Jon Elson
2003-07-05 22:27:30 UTC
Re: [CAD_CAM_EDM_DRO] gecko's and voltage
Mariss Freimanis
2003-07-05 22:29:42 UTC
Re: gecko's and voltage
Kim Lux
2003-07-05 22:43:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Kim Lux
2003-07-05 23:06:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
rotarysmp
2003-07-06 01:56:59 UTC
Re: gecko's and voltage
stevenson_engineers
2003-07-06 05:47:38 UTC
Re: gecko's and voltage
mmurray701
2003-07-06 08:40:14 UTC
Re: gecko's and voltage
Tim Goldstein
2003-07-06 09:29:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
turbulatordude
2003-07-06 10:09:57 UTC
Re: gecko's and voltage - Gecko Warrantee
cnchomeman
2003-07-06 10:32:26 UTC
Re: gecko's and voltage
cnchomeman
2003-07-06 10:33:26 UTC
Re: gecko's and voltage - Gecko Warrantee
turbulatordude
2003-07-06 10:34:52 UTC
Re: gecko's and voltage
Lee Studley
2003-07-06 12:19:06 UTC
Re: gecko's and voltage
Jon Elson
2003-07-06 12:50:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage - Gecko Warrantee
Kim Lux
2003-07-06 21:39:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Mariss Freimanis
2003-07-06 23:03:30 UTC
Re: gecko's and voltage
Tony Jeffree
2003-07-06 23:35:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Tony Jeffree
2003-07-07 00:48:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
Vince Negrete
2003-07-07 02:46:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko's and voltage
turbulatordude
2003-07-07 06:22:54 UTC
Re: gecko's and voltage
mmurray701
2003-07-07 08:22:27 UTC
Re: gecko's and voltage
washcomp
2003-08-15 19:55:33 UTC
Re: gecko's and voltage - For Mariss