CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] mach3 question

Posted by Leslie Newell
on 2009-12-04 08:39:42 UTC
Hi Chuck,

Are the keys the wrong way round? The right key should move the table
left. This seems wrong but it is correct. The jog keys should control
the cutter's position relative to the work. Imagine you are stood on the
table. Pressing the right key moves the table left so as you are moving
with the table the cutter moves to your right.

Les

ebiz_59 wrote:
> Our science and tech club finally got a used minimill (X2) with cnc and Xylotec controller running using Mach3. Woohoo, we have entered the 21st century! One issue we are having though is that when running the mill using Mach3 and the computer keyboard, the key directions seem to be reversed. Where did we mess up in setup? Is that in the configuration of pins setup?? This is all new to us and way cool to actually see something move, but then we realized XY and ?Z? were all moving opposite the direction of the arrow keys - took a little wind out of our sails. thanks, Chuck
>
>
>

Discussion Thread

ebiz_59 2009-12-04 08:11:58 UTC mach3 question Jack McKie 2009-12-04 08:21:33 UTC Re: [CAD_CAM_EDM_DRO] mach3 question Dan Mauch 2009-12-04 08:23:09 UTC mach3 question Leslie Newell 2009-12-04 08:39:42 UTC Re: [CAD_CAM_EDM_DRO] mach3 question Art Eckstein 2009-12-04 08:48:50 UTC Re: [CAD_CAM_EDM_DRO] mach3 question Chuck Merja 2009-12-04 09:33:30 UTC RE: [CAD_CAM_EDM_DRO] mach3 question Chuck Merja 2009-12-04 09:33:44 UTC RE: [CAD_CAM_EDM_DRO] mach3 question Chuck Merja 2009-12-04 22:23:46 UTC RE: [CAD_CAM_EDM_DRO] mach3 question_2 Dave Halliday 2009-12-04 23:43:36 UTC RE: [CAD_CAM_EDM_DRO] mach3 question Danny Miller 2009-12-04 23:53:13 UTC Re: [CAD_CAM_EDM_DRO] mach3 question_2 Dan Mauch 2009-12-05 12:21:53 UTC Re: [CAD_CAM_EDM_DRO] mach3 question_2 Roland Jollivet 2009-12-05 12:22:07 UTC Re: [CAD_CAM_EDM_DRO] mach3 question_2 Alfredo Sola 2009-12-05 12:22:11 UTC Hello imserv1 2009-12-06 08:23:05 UTC Re: Hello johann_ohnesorg 2009-12-07 15:32:04 UTC Re: Hello Chuck Merja 2009-12-10 04:03:11 UTC Re: [CAD_CAM_EDM_DRO] mach3 question_2 Alfredo Sola 2009-12-10 19:20:57 UTC Couplings johann_ohnesorg 2009-12-11 09:39:05 UTC Re: Couplings Andrew Werby 2009-12-11 11:18:18 UTC Re: Couplings 556RECON 2009-12-11 15:49:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Couplings Will Holding 2009-12-11 21:13:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Couplings cncnovice 2009-12-12 10:55:49 UTC Re: Couplings cncnovice 2009-12-12 11:00:31 UTC Re: Couplings Andrew Werby 2009-12-13 12:22:16 UTC Couplings Peter Homann 2009-12-13 14:48:02 UTC Re: [CAD_CAM_EDM_DRO] Couplings david@f... 2009-12-13 23:09:39 UTC Re: [CAD_CAM_EDM_DRO] Couplings tjwal 2009-12-14 09:12:38 UTC Re: Couplings Alfredo Sola 2009-12-14 21:26:47 UTC Couplings diazden 2009-12-14 23:01:47 UTC Re: Couplings rhaag71 2009-12-30 15:59:44 UTC Re: Couplings Randall Wink 2009-12-31 12:41:56 UTC RE: [CAD_CAM_EDM_DRO] Re: Couplings