RE: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Posted by
Chuck Merja
on 2011-11-15 22:14:44 UTC
Well, my initial diagnosis of the power supply might have not been the whole
problem. I plugged in a 19V 4.5A laptop power supply that had an open
circuit voltage of 19.8 ish and the green light on the power supply went
out, and the voltage to the controller was 0. I'm a rank amateur, but I'm
thinking that isn't good. So the 24V 6.5A replacement PS I ordered should
be here by Fri, but I'm thinking I should somehow test the Xylotex drivers
to see if they are any good. Suggestions? Cuz I'd like not to just plug in
that new PS and have it come to an early demise.
And yes, I'll probably just get a set of Geckos - G540's (with one
dissenting vote due to not being able to stop one axis is my current tally)
- yes?
I'm pretty sure the current steppers are Automation Direct Sure Step, NEMA
23, 276oz-in.
<http://www.automationdirect.com/adc/Shopping/Catalog/Motion_Control/Stepper
_Systems/Motors_-z-_Cables/STP-MTR-23079>
Should I get bigger motors too, or try the new driver on these steppers?
Thanks, Chuck
problem. I plugged in a 19V 4.5A laptop power supply that had an open
circuit voltage of 19.8 ish and the green light on the power supply went
out, and the voltage to the controller was 0. I'm a rank amateur, but I'm
thinking that isn't good. So the 24V 6.5A replacement PS I ordered should
be here by Fri, but I'm thinking I should somehow test the Xylotex drivers
to see if they are any good. Suggestions? Cuz I'd like not to just plug in
that new PS and have it come to an early demise.
And yes, I'll probably just get a set of Geckos - G540's (with one
dissenting vote due to not being able to stop one axis is my current tally)
- yes?
I'm pretty sure the current steppers are Automation Direct Sure Step, NEMA
23, 276oz-in.
<http://www.automationdirect.com/adc/Shopping/Catalog/Motion_Control/Stepper
_Systems/Motors_-z-_Cables/STP-MTR-23079>
Should I get bigger motors too, or try the new driver on these steppers?
Thanks, Chuck
On 11/13/2011 02:02 AM, ebiz_59 wrote:
> Any other thots? And what are the odds that the Xylotex drives are OK if
this power supply board is only putting out like 1.5V? Should I be looking
for another set of stepper drivers too?
You might want to look at
http://www.mpja.com/25VDC-10A-Power-Supply/productinfo/18960+PS/, MPJA
will sell you one for $20! Of course, they have a lot of other (much
more expensive) supplies like
http://www.mpja.com/48V-15A-Hengfu-Power-Supply/productinfo/16510+PS/
which, for $220, isn't cheap, but 48 Volts at 15A is not trivial.
Hope this helps.
Dave 8{)
--
/"Political Correctness is a doctrine, fostered by a delusional,
illogical minority and rabidly promoted by an unscrupulous mainstream
media, which holds forth the proposition that it is entirely possible to
pick up a turd by the clean end."/
(quoted from http://www.wattflyer.com/forums/showthread.php?t=30060)
NOTE TO ALL:
._,___
[Non-text portions of this message have been removed]
Discussion Thread
ebiz_59
2011-11-12 23:02:30 UTC
Xylotex Pwr Sup replacement
Danny Miller
2011-11-12 23:18:51 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Michael Fagan
2011-11-13 06:52:07 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
"hanermo" - CNC 6-axis Designs
2011-11-13 07:16:19 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Michael Fagan
2011-11-13 07:19:26 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
turbulatordude
2011-11-13 09:08:22 UTC
Re: Xylotex Pwr Sup replacement
Chuck Merja
2011-11-13 10:22:59 UTC
RE: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Danny Miller
2011-11-13 14:11:02 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Dave Halliday
2011-11-13 14:36:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Danny Miller
2011-11-13 14:58:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
turbulatordude
2011-11-13 16:01:52 UTC
Re: Xylotex Pwr Sup replacement
Danny Miller
2011-11-13 16:27:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
turbulatordude
2011-11-13 17:34:38 UTC
Re: Xylotex Pwr Sup replacement
turbulatordude
2011-11-13 17:38:18 UTC
Re: Xylotex Pwr Sup replacement
turbulatordude
2011-11-13 17:46:21 UTC
Re: Xylotex Pwr Sup replacement
Danny Miller
2011-11-13 18:15:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Andy Wander
2011-11-13 18:37:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Dave Halliday
2011-11-13 21:07:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Dave Halliday
2011-11-13 21:07:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Danny Miller
2011-11-13 23:48:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
turbulatordude
2011-11-14 01:02:04 UTC
Re: Xylotex Pwr Sup replacement
chuck
2011-11-14 01:10:50 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
turbulatordude
2011-11-14 01:16:21 UTC
automation direct sure step
"hanermo" - CNC 6-axis Designs
2011-11-14 01:35:15 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Andy Wander
2011-11-14 06:15:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: Xylotex Pwr Sup replacement
Chuck Merja
2011-11-14 07:24:15 UTC
RE: [CAD_CAM_EDM_DRO] automation direct sure step
David G. LeVine
2011-11-14 10:37:30 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
"hanermo" - CNC 6-axis Designs
2011-11-14 11:43:34 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Danny Miller
2011-11-14 11:52:59 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
turbulatordude
2011-11-14 18:04:01 UTC
mini-mill and motors
Danny Miller
2011-11-14 22:31:51 UTC
Re: [CAD_CAM_EDM_DRO] mini-mill and motors
turbulatordude
2011-11-15 02:59:25 UTC
Re: mini-mill and motors
Chuck Merja
2011-11-15 22:14:44 UTC
RE: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
"hanermo" - CNC 6-axis Designs
2011-11-16 00:59:33 UTC
Re: [CAD_CAM_EDM_DRO] mini-mill and motors
turbulatordude
2011-11-16 04:27:07 UTC
Re: Xylotex Pwr Sup replacement
Ron Thompson
2011-11-16 05:19:26 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement
Chuck Merja
2011-11-17 08:02:40 UTC
RE: [CAD_CAM_EDM_DRO] Gecko G540
Ron Thompson
2011-11-17 08:43:34 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G540
Michael Fagan
2011-11-17 11:24:43 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G540
Peter Homann
2011-11-17 12:54:52 UTC
Re: [CAD_CAM_EDM_DRO] Gecko G540
robin
2012-01-16 11:03:22 UTC
Re: [CAD_CAM_EDM_DRO] Xylotex Pwr Sup replacement