CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater

Posted by diazden
on 2000-12-20 06:03:47 UTC
> Tim;
> in my opinion the best (an cheapest heater to run) is hot water,I explain myself:
> when you are constructing your workshop ,before you pour the concrete
> lay 1/2 copper pipes along side at a distance of about 2 ft for the length of the
> garage ,all the pipes should be connected between them , pour the concrete to
> cover the pipes about 2" on top and when you finish the workshop hook them
> up to the house hot water supply , you could also use a solar water heater and
> whatever is your fuel for the household hot water for boost ,as the heat travels
> up you would have the most warm workshop in the neighborhood , don't forget
> that if the floor is warm you are warm as well. This method is used in the houses
> in Europe.
> regards and happy xmas
>
> mariano
>
> Tim Goldstein wrote:
>
> > I am in the process of relocating my workshop from the basement to the
> > garage. I don't have my heater installed yet, but have already gotten the
> > lines put in for a natural gas unit heater. I am planning on going with a
> > 45,000 BTU unit. This is just a guess as to the proper size. Can anyone help
> > me understand how I would determine the correct size furnace to heat an
> > insulated 2 car garage in Denver, CO?
> >
> > Tim
> > [Denver, CO]
> >
> > > FAQ: http://www.ktmarketing.com/faq.html
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager

Discussion Thread

marco@m... 2000-12-19 07:44:08 UTC OT: Intro + Q:Selecting workshop heater Jon Anderson 2000-12-19 08:30:00 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Joe Fahy 2000-12-19 09:56:39 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Marcus & Eva 2000-12-19 10:49:44 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-19 10:53:35 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-19 10:55:25 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Steve Gunsel 2000-12-19 11:00:38 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-19 11:04:54 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater John Murphy 2000-12-19 11:39:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Marconett KM6VV 2000-12-19 12:28:16 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Wally K 2000-12-19 14:22:47 UTC Re: OT: Intro + Q:Selecting workshop heater James Owens 2000-12-19 15:34:50 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Rothenbush 2000-12-19 16:24:23 UTC Re: OT: Intro + Q:Selecting workshop heater dave engvall 2000-12-19 16:52:26 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater marble here 2000-12-19 20:33:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater diazden 2000-12-19 20:57:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-19 21:11:33 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Jeff Barlow 2000-12-19 21:25:50 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Joe Fahy 2000-12-19 21:55:38 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Jon Elson 2000-12-19 22:23:03 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-20 01:45:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater diazden 2000-12-20 06:03:47 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-20 06:24:30 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-20 06:24:32 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-20 06:24:34 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater BillDarby 2000-12-20 06:54:24 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Doug Harrison 2000-12-20 07:50:24 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Marconett KM6VV 2000-12-20 10:35:47 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater ballendo@y... 2000-12-20 13:41:10 UTC re:Re: OT: Intro + Q:Selecting workshop heater ballendo@y... 2000-12-20 16:11:45 UTC Re: OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-21 04:42:16 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater James Owens 2000-12-21 07:24:23 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-21 10:39:45 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Marconett KM6VV 2000-12-21 10:57:03 UTC Re: OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-21 13:44:51 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater James Owens 2000-12-22 02:23:19 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tony Jeffree 2000-12-22 02:48:40 UTC Re: OT: Intro + Q:Selecting workshop heater Smoke 2000-12-22 09:13:18 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-22 14:51:41 UTC Re: [CAD_CAM_EDM_DRO] Re: OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-22 14:54:03 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-22 15:18:57 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater dave engvall 2000-12-28 18:54:11 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-28 19:16:58 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater dave engvall 2000-12-28 22:47:34 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-28 23:06:59 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater