CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater

Posted by Doug Harrison
on 2000-12-20 07:50:24 UTC
----- Original Message -----
From: Tim Goldstein <timg@...>

> The heaters I am looking at all vent the combustion products out doors.
So,
> the heating has a drying effect and no additional moisture is added to the
> indoor air. In Colorado rust is not a major problem. I agree that using a
> non vented heater is a dicey proposition. Besides the moisture there are
> concerns about the CO2 and CO buildup.
>
> Tim
> [Denver, CO]

Good morning Tim;

I have talked to a few boat builders that use propane water heaters for
heating work areas. The outlet runs to a copper or cpvc line that runs the
perimeter of the shop. Prior to re-entering the heater it goes through a
hot water recirculation pump. A small reservoir (2-4 gal.) is placed above
the heater and tied into the return to maintain a full tank. Pressurization
is not necessary, though you may want to turn the temp down a bit.

We just purchased a cheap 40 gallon heater for this purpose but have not
installed it yet. The capacity is 34K BTU. The advantage of this system is
that you can put the heater in a separate enclosure outside to eliminate the
risk associated with the open flame. An additional benefit is that the HWH
is cheaper than a space heater. Tie a thermostat to the pump and you have
good temp control as well.

Doug Harrison

Discussion Thread

marco@m... 2000-12-19 07:44:08 UTC OT: Intro + Q:Selecting workshop heater Jon Anderson 2000-12-19 08:30:00 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Joe Fahy 2000-12-19 09:56:39 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Marcus & Eva 2000-12-19 10:49:44 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-19 10:53:35 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-19 10:55:25 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Steve Gunsel 2000-12-19 11:00:38 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-19 11:04:54 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater John Murphy 2000-12-19 11:39:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Marconett KM6VV 2000-12-19 12:28:16 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Wally K 2000-12-19 14:22:47 UTC Re: OT: Intro + Q:Selecting workshop heater James Owens 2000-12-19 15:34:50 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Rothenbush 2000-12-19 16:24:23 UTC Re: OT: Intro + Q:Selecting workshop heater dave engvall 2000-12-19 16:52:26 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater marble here 2000-12-19 20:33:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater diazden 2000-12-19 20:57:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-19 21:11:33 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Jeff Barlow 2000-12-19 21:25:50 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Joe Fahy 2000-12-19 21:55:38 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Jon Elson 2000-12-19 22:23:03 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-20 01:45:30 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater diazden 2000-12-20 06:03:47 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-20 06:24:30 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-20 06:24:32 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tim Goldstein 2000-12-20 06:24:34 UTC RE: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater BillDarby 2000-12-20 06:54:24 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Doug Harrison 2000-12-20 07:50:24 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Marconett KM6VV 2000-12-20 10:35:47 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater ballendo@y... 2000-12-20 13:41:10 UTC re:Re: OT: Intro + Q:Selecting workshop heater ballendo@y... 2000-12-20 16:11:45 UTC Re: OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-21 04:42:16 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater James Owens 2000-12-21 07:24:23 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-21 10:39:45 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Alan Marconett KM6VV 2000-12-21 10:57:03 UTC Re: OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-21 13:44:51 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater James Owens 2000-12-22 02:23:19 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Tony Jeffree 2000-12-22 02:48:40 UTC Re: OT: Intro + Q:Selecting workshop heater Smoke 2000-12-22 09:13:18 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-22 14:51:41 UTC Re: [CAD_CAM_EDM_DRO] Re: OT: Intro + Q:Selecting workshop heater Ian Wright 2000-12-22 14:54:03 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-22 15:18:57 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater dave engvall 2000-12-28 18:54:11 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-28 19:16:58 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater dave engvall 2000-12-28 22:47:34 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater Smoke 2000-12-28 23:06:59 UTC Re: [CAD_CAM_EDM_DRO] OT: Intro + Q:Selecting workshop heater