CAD CAM EDM DRO - Yahoo Group Archive

Re: Chopper circuit

Posted by dave_ace_me
on 2002-04-04 19:50:29 UTC
> I need to look at the 7805 input voltage - can someone suggest a
> suitable way of feeding it at more than 15v or so?


The 7805 will get hot if it has to drop too much voltage. It can work
from a 7812 (or less) as they will drop the voltage in stages. Each
dissapating watts in heat, and neither overheating.

also, you can use up to about 24 (28?) volts with the 7805, but you
must use a heatsink. Check the spec sheet.

Dave

Discussion Thread

Steve Blackmore 2002-03-27 16:57:25 UTC Chopper circuit pfrederick1 2002-03-28 05:41:01 UTC Re: Chopper circuit Vajk Fekete 2002-03-28 06:19:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit stephen_stallings 2002-03-28 12:05:30 UTC Re: Chopper circuit pfrederick1 2002-03-28 12:25:46 UTC Re: Chopper circuit Tony Jeffree 2002-03-28 13:46:18 UTC Re: Chopper circuit Steve Blackmore 2002-03-28 20:38:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit RichD. 2002-03-28 21:12:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit Steve Blackmore 2002-03-29 03:34:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit Steve Blackmore 2002-04-02 12:07:07 UTC Chopper circuit waynegramlich 2002-04-02 20:02:49 UTC Re: Chopper circuit Steve Blackmore 2002-04-03 11:16:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit paul_alz 2002-04-03 15:46:51 UTC Re: Chopper circuit andrewyslee 2002-04-03 15:54:29 UTC safety Chris L 2002-04-03 16:28:58 UTC Re: [CAD_CAM_EDM_DRO] safety waynegramlich 2002-04-03 16:36:57 UTC Re: Chopper circuit waynegramlich 2002-04-03 16:41:50 UTC Re: Chopper circuit JanRwl@A... 2002-04-03 16:46:35 UTC Re: [CAD_CAM_EDM_DRO] safety andrewyslee 2002-04-03 17:45:36 UTC Re: safety JanRwl@A... 2002-04-03 18:31:59 UTC Re: [CAD_CAM_EDM_DRO] Re: safety mariss92705 2002-04-03 19:01:55 UTC Re: Chopper circuit Raymond Heckert 2002-04-03 23:16:06 UTC Re: [CAD_CAM_EDM_DRO] safety waynegramlich 2002-04-04 09:37:54 UTC L298 Commutation Diodes (was Re: Chopper circuit) paul_alz 2002-04-04 15:55:03 UTC Re: Chopper circuit mariss92705 2002-04-04 16:51:05 UTC L298 Commutation Diodes (was Re: Chopper circuit) Raymond Heckert 2002-04-04 19:35:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit dave_ace_me 2002-04-04 19:50:29 UTC Re: Chopper circuit dave_ace_me 2002-04-04 19:55:25 UTC OT irfranview ( was Re: Chopper circuit waynegramlich 2002-04-04 21:18:39 UTC Re: Chopper circuit waynegramlich 2002-04-04 21:36:16 UTC L298 Commutation Diodes (was Re: Chopper circuit) paul_alz 2002-04-04 23:49:13 UTC Re: Chopper circuit dave_ace_me 2002-04-05 05:39:10 UTC Re: Chopper circuit paul_alz 2002-04-06 01:04:04 UTC Re: Chopper circuit ballendo 2002-04-06 06:47:08 UTC Re: Chopper circuit JanRwl@A... 2002-04-06 13:21:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit mariss92705 2002-04-06 14:06:59 UTC Re: Chopper circuit Steve Blackmore 2002-04-06 16:50:32 UTC [CAD_CAM_EDM_DRO] Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-07 03:19:03 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-07 05:00:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-07 09:47:58 UTC Re: Was Chopper circuit - Now ver 3.2 n4onl 2002-04-07 10:20:22 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-07 12:31:11 UTC Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-07 13:26:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 n4onl 2002-04-07 15:53:03 UTC Re: Was Chopper circuit - Now ver 3.2 waynegramlich 2002-04-07 17:21:57 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-07 18:05:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-07 18:07:59 UTC Re: Was Chopper circuit - Now ver 3.2 Tim Goldstein 2002-04-07 19:04:37 UTC RE: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-07 19:43:07 UTC Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-07 20:00:17 UTC Re: Was Chopper circuit - Now ver 3.2 RichD 2002-04-07 20:08:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 marble here 2002-04-07 20:40:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Tim Goldstein 2002-04-07 20:54:18 UTC RE: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 marble here 2002-04-07 21:05:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 marble here 2002-04-07 21:09:10 UTC RE: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-07 22:13:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Doug Fortune 2002-04-07 22:33:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Paul Weber 2002-04-07 23:28:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Tony Jeffree 2002-04-07 23:42:39 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-08 00:45:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-08 00:49:48 UTC Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-08 01:01:35 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 01:13:38 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-08 01:17:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 02:05:30 UTC Re: Was Chopper circuit - Now ver 3.2 Tony Jeffree 2002-04-08 02:14:33 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 02:29:31 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 02:40:50 UTC Re: Was Chopper circuit - Now ver 3.2 Paul R. Hvidston 2002-04-08 07:41:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 cadcamcenter 2002-04-08 08:40:22 UTC Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-08 21:37:12 UTC Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-08 21:57:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-08 22:17:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-08 22:28:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-08 22:36:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 RichD 2002-04-08 22:51:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-09 00:08:36 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-09 01:01:27 UTC Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-09 10:14:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-09 10:36:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-09 11:54:39 UTC Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-09 22:44:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-10 04:01:07 UTC Re: Was Chopper circuit - Ver 3.2 Web page up ballendo 2002-04-13 05:31:51 UTC Re: safety andrewyslee 2002-04-13 16:01:35 UTC Re: safety wanliker@a... 2002-04-13 23:27:38 UTC Re: [CAD_CAM_EDM_DRO] Re: safety ballendo 2002-04-14 01:06:45 UTC Re: Was Chopper circuit - Now ver 3.2 ballendo 2002-04-14 03:44:04 UTC pcb sources was Re: Was Chopper circuit - Now ver 3.2 dave_ace_me 2002-04-14 06:31:41 UTC pcb sources was Re: Was Chopper circuit - Now ver 3.2 JanRwl@A... 2002-04-14 16:51:19 UTC Re: [CAD_CAM_EDM_DRO] Re: safety andrewyslee 2002-04-14 17:52:15 UTC safety - pcb dust hazard mariss92705 2002-04-14 18:06:00 UTC Re: safety - pcb dust hazard mariss92705 2002-04-14 18:10:08 UTC Re: safety andrewyslee 2002-04-14 18:39:49 UTC Re: safety - pcb dust hazard Sven Peter 2002-04-14 18:53:27 UTC Re: [CAD_CAM_EDM_DRO] safety - pcb dust hazard marble_h 2002-04-14 19:27:38 UTC Re: safety - pcb dust hazard J.Critchfield 2002-04-14 20:09:15 UTC Re: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard JanRwl@A... 2002-04-15 00:01:23 UTC Re: [CAD_CAM_EDM_DRO] Re: safety JanRwl@A... 2002-04-15 00:05:02 UTC Re: [CAD_CAM_EDM_DRO] Re: safety dave_ace_me 2002-04-15 04:05:04 UTC Re: safety - pcb dust hazard andrewyslee 2002-04-15 17:45:42 UTC Re: safety - pcb dust hazard andrewyslee 2002-04-15 18:17:13 UTC Re: safety - pcb dust hazard ballendo 2002-04-16 13:58:59 UTC Re: safety - pcb dust hazard Raymond Heckert 2002-04-16 16:01:33 UTC Re: [CAD_CAM_EDM_DRO] Re: safety ballendo 2002-04-16 16:44:40 UTC Re: safety - pcb dust hazard ballendo 2002-04-17 01:23:05 UTC What to do in an estop ?!? was Re: safety mariss92705 2002-04-17 03:03:29 UTC Re: safety Sven Peter 2002-04-17 06:49:42 UTC Re: [CAD_CAM_EDM_DRO] Re: safety mariss92705 2002-04-17 07:23:55 UTC Re: safety - pcb dust hazard dave_ace_me 2002-04-17 10:02:12 UTC Re: safety - pcb dust hazard mariss92705 2002-04-17 10:53:38 UTC Re: safety - pcb dust hazard dave_ace_me 2002-04-17 20:07:33 UTC Re: safety - pcb dust hazard askforum 2002-04-17 20:07:55 UTC Re: safety - pcb dust hazard JanRwl@A... 2002-04-17 20:30:05 UTC Re: [CAD_CAM_EDM_DRO] Re: safety mariss92705 2002-04-17 22:23:42 UTC Re: safety - pcb dust hazard Ward 2002-04-18 01:14:10 UTC RE: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard batwings@i... 2002-04-18 04:30:08 UTC RE: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard dave_ace_me 2002-04-18 04:57:56 UTC Re: safety - pcb dust hazard steveggca 2002-04-18 05:00:12 UTC What to do in an estop ?!? was Re: safety Jon Elson 2002-04-18 05:42:20 UTC Re: [CAD_CAM_EDM_DRO] Re: safety Raymond Heckert 2002-04-18 09:51:38 UTC Re: [CAD_CAM_EDM_DRO] What to do in an estop ?!? was Re: safety Jon Elson 2002-04-18 10:59:03 UTC Re: [CAD_CAM_EDM_DRO] What to do in an estop ?!? was Re: safety mariss92705 2002-04-18 11:45:34 UTC Re: safety Jon Elson 2002-04-18 23:06:48 UTC Re: [CAD_CAM_EDM_DRO] Re: safety Hugh Prescott 2002-04-19 01:28:37 UTC Re: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard ballendo 2002-04-19 06:16:34 UTC OT Re: safety - pcb dust hazard