CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2

on 2002-04-08 22:36:50 UTC
----- Original Message -----
From: "mariss92705" <mariss92705@...>
> Just an errant thought here. Would anyone be interested if I were to
> cobble-up a single or dual bridge, all n-channel MOSFET (TO-220,
> IRF540) power driver? This would be on a 4-layer PCB and include all
> necessary supply bypassing, TTL input interface and a current sense
> resistor.

Running the 2104 in standard boost mode with a cap? Then it'll have to be
run on a chopping drive right? I just don't want someone to end up putting
a steady state drive signal on an input and their boost cap ends up
discharging
below minimum vgs then the high side fet gets unhappy.

An oscillator would fix that but now you are into more complexity and cost.

I assume you intended these to be for standard chopping drives so I thought
I'd just mention it. I used 2104's to drive IRF540's for a chopping drive
that
worked out great. They don't like to be left on too long though.

later,
Larry E.

Discussion Thread

Steve Blackmore 2002-03-27 16:57:25 UTC Chopper circuit pfrederick1 2002-03-28 05:41:01 UTC Re: Chopper circuit Vajk Fekete 2002-03-28 06:19:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit stephen_stallings 2002-03-28 12:05:30 UTC Re: Chopper circuit pfrederick1 2002-03-28 12:25:46 UTC Re: Chopper circuit Tony Jeffree 2002-03-28 13:46:18 UTC Re: Chopper circuit Steve Blackmore 2002-03-28 20:38:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit RichD. 2002-03-28 21:12:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit Steve Blackmore 2002-03-29 03:34:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit Steve Blackmore 2002-04-02 12:07:07 UTC Chopper circuit waynegramlich 2002-04-02 20:02:49 UTC Re: Chopper circuit Steve Blackmore 2002-04-03 11:16:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit paul_alz 2002-04-03 15:46:51 UTC Re: Chopper circuit andrewyslee 2002-04-03 15:54:29 UTC safety Chris L 2002-04-03 16:28:58 UTC Re: [CAD_CAM_EDM_DRO] safety waynegramlich 2002-04-03 16:36:57 UTC Re: Chopper circuit waynegramlich 2002-04-03 16:41:50 UTC Re: Chopper circuit JanRwl@A... 2002-04-03 16:46:35 UTC Re: [CAD_CAM_EDM_DRO] safety andrewyslee 2002-04-03 17:45:36 UTC Re: safety JanRwl@A... 2002-04-03 18:31:59 UTC Re: [CAD_CAM_EDM_DRO] Re: safety mariss92705 2002-04-03 19:01:55 UTC Re: Chopper circuit Raymond Heckert 2002-04-03 23:16:06 UTC Re: [CAD_CAM_EDM_DRO] safety waynegramlich 2002-04-04 09:37:54 UTC L298 Commutation Diodes (was Re: Chopper circuit) paul_alz 2002-04-04 15:55:03 UTC Re: Chopper circuit mariss92705 2002-04-04 16:51:05 UTC L298 Commutation Diodes (was Re: Chopper circuit) Raymond Heckert 2002-04-04 19:35:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit dave_ace_me 2002-04-04 19:50:29 UTC Re: Chopper circuit dave_ace_me 2002-04-04 19:55:25 UTC OT irfranview ( was Re: Chopper circuit waynegramlich 2002-04-04 21:18:39 UTC Re: Chopper circuit waynegramlich 2002-04-04 21:36:16 UTC L298 Commutation Diodes (was Re: Chopper circuit) paul_alz 2002-04-04 23:49:13 UTC Re: Chopper circuit dave_ace_me 2002-04-05 05:39:10 UTC Re: Chopper circuit paul_alz 2002-04-06 01:04:04 UTC Re: Chopper circuit ballendo 2002-04-06 06:47:08 UTC Re: Chopper circuit JanRwl@A... 2002-04-06 13:21:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Chopper circuit mariss92705 2002-04-06 14:06:59 UTC Re: Chopper circuit Steve Blackmore 2002-04-06 16:50:32 UTC [CAD_CAM_EDM_DRO] Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-07 03:19:03 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-07 05:00:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-07 09:47:58 UTC Re: Was Chopper circuit - Now ver 3.2 n4onl 2002-04-07 10:20:22 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-07 12:31:11 UTC Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-07 13:26:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 n4onl 2002-04-07 15:53:03 UTC Re: Was Chopper circuit - Now ver 3.2 waynegramlich 2002-04-07 17:21:57 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-07 18:05:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-07 18:07:59 UTC Re: Was Chopper circuit - Now ver 3.2 Tim Goldstein 2002-04-07 19:04:37 UTC RE: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-07 19:43:07 UTC Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-07 20:00:17 UTC Re: Was Chopper circuit - Now ver 3.2 RichD 2002-04-07 20:08:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 marble here 2002-04-07 20:40:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Tim Goldstein 2002-04-07 20:54:18 UTC RE: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 marble here 2002-04-07 21:05:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 marble here 2002-04-07 21:09:10 UTC RE: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-07 22:13:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Doug Fortune 2002-04-07 22:33:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Paul Weber 2002-04-07 23:28:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Tony Jeffree 2002-04-07 23:42:39 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-08 00:45:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-08 00:49:48 UTC Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-08 01:01:35 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 01:13:38 UTC Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-08 01:17:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 02:05:30 UTC Re: Was Chopper circuit - Now ver 3.2 Tony Jeffree 2002-04-08 02:14:33 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 02:29:31 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-08 02:40:50 UTC Re: Was Chopper circuit - Now ver 3.2 Paul R. Hvidston 2002-04-08 07:41:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 cadcamcenter 2002-04-08 08:40:22 UTC Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-08 21:37:12 UTC Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-08 21:57:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-08 22:17:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-08 22:28:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Larry Edington 2002-04-08 22:36:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 RichD 2002-04-08 22:51:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-09 00:08:36 UTC Re: Was Chopper circuit - Now ver 3.2 paul_alz 2002-04-09 01:01:27 UTC Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-09 10:14:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-09 10:36:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 mariss92705 2002-04-09 11:54:39 UTC Re: Was Chopper circuit - Now ver 3.2 Jon Elson 2002-04-09 22:44:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Was Chopper circuit - Now ver 3.2 Steve Blackmore 2002-04-10 04:01:07 UTC Re: Was Chopper circuit - Ver 3.2 Web page up ballendo 2002-04-13 05:31:51 UTC Re: safety andrewyslee 2002-04-13 16:01:35 UTC Re: safety wanliker@a... 2002-04-13 23:27:38 UTC Re: [CAD_CAM_EDM_DRO] Re: safety ballendo 2002-04-14 01:06:45 UTC Re: Was Chopper circuit - Now ver 3.2 ballendo 2002-04-14 03:44:04 UTC pcb sources was Re: Was Chopper circuit - Now ver 3.2 dave_ace_me 2002-04-14 06:31:41 UTC pcb sources was Re: Was Chopper circuit - Now ver 3.2 JanRwl@A... 2002-04-14 16:51:19 UTC Re: [CAD_CAM_EDM_DRO] Re: safety andrewyslee 2002-04-14 17:52:15 UTC safety - pcb dust hazard mariss92705 2002-04-14 18:06:00 UTC Re: safety - pcb dust hazard mariss92705 2002-04-14 18:10:08 UTC Re: safety andrewyslee 2002-04-14 18:39:49 UTC Re: safety - pcb dust hazard Sven Peter 2002-04-14 18:53:27 UTC Re: [CAD_CAM_EDM_DRO] safety - pcb dust hazard marble_h 2002-04-14 19:27:38 UTC Re: safety - pcb dust hazard J.Critchfield 2002-04-14 20:09:15 UTC Re: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard JanRwl@A... 2002-04-15 00:01:23 UTC Re: [CAD_CAM_EDM_DRO] Re: safety JanRwl@A... 2002-04-15 00:05:02 UTC Re: [CAD_CAM_EDM_DRO] Re: safety dave_ace_me 2002-04-15 04:05:04 UTC Re: safety - pcb dust hazard andrewyslee 2002-04-15 17:45:42 UTC Re: safety - pcb dust hazard andrewyslee 2002-04-15 18:17:13 UTC Re: safety - pcb dust hazard ballendo 2002-04-16 13:58:59 UTC Re: safety - pcb dust hazard Raymond Heckert 2002-04-16 16:01:33 UTC Re: [CAD_CAM_EDM_DRO] Re: safety ballendo 2002-04-16 16:44:40 UTC Re: safety - pcb dust hazard ballendo 2002-04-17 01:23:05 UTC What to do in an estop ?!? was Re: safety mariss92705 2002-04-17 03:03:29 UTC Re: safety Sven Peter 2002-04-17 06:49:42 UTC Re: [CAD_CAM_EDM_DRO] Re: safety mariss92705 2002-04-17 07:23:55 UTC Re: safety - pcb dust hazard dave_ace_me 2002-04-17 10:02:12 UTC Re: safety - pcb dust hazard mariss92705 2002-04-17 10:53:38 UTC Re: safety - pcb dust hazard dave_ace_me 2002-04-17 20:07:33 UTC Re: safety - pcb dust hazard askforum 2002-04-17 20:07:55 UTC Re: safety - pcb dust hazard JanRwl@A... 2002-04-17 20:30:05 UTC Re: [CAD_CAM_EDM_DRO] Re: safety mariss92705 2002-04-17 22:23:42 UTC Re: safety - pcb dust hazard Ward 2002-04-18 01:14:10 UTC RE: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard batwings@i... 2002-04-18 04:30:08 UTC RE: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard dave_ace_me 2002-04-18 04:57:56 UTC Re: safety - pcb dust hazard steveggca 2002-04-18 05:00:12 UTC What to do in an estop ?!? was Re: safety Jon Elson 2002-04-18 05:42:20 UTC Re: [CAD_CAM_EDM_DRO] Re: safety Raymond Heckert 2002-04-18 09:51:38 UTC Re: [CAD_CAM_EDM_DRO] What to do in an estop ?!? was Re: safety Jon Elson 2002-04-18 10:59:03 UTC Re: [CAD_CAM_EDM_DRO] What to do in an estop ?!? was Re: safety mariss92705 2002-04-18 11:45:34 UTC Re: safety Jon Elson 2002-04-18 23:06:48 UTC Re: [CAD_CAM_EDM_DRO] Re: safety Hugh Prescott 2002-04-19 01:28:37 UTC Re: [CAD_CAM_EDM_DRO] Re: safety - pcb dust hazard ballendo 2002-04-19 06:16:34 UTC OT Re: safety - pcb dust hazard