CAD CAM EDM DRO - Yahoo Group Archive

Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D

Posted by cncgramps
on 2006-01-21 10:33:50 UTC
About the only size that will fit and still be big enough is the
5/8" ballscrew. I was able to use a double nut on my X and Y but the
Z only had room for a single ballnut.
If you plan on doing anything with fine detail in the Z I would
again recommend hooking up a ball screw for the Z.
I have done some engravings from photos that need have very small Z
movements that I do not think you could get without the ballscrew on
the Z.
What I did was clamped around the bottom of the quill with a
bracket that the ballscrew attached to.
I was lucky enough to have access to a Bridgeport EZ track when I
made my brackets so it was pretty easy going. Once I had the XY
going I finished some of the Z parts on my own mill.
Good luck and if you need any information feel free to ask. Or
pictures of what my parts looked like.

Gary

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Darren Lucke
<oneluckeboy@y...> wrote:
>
> Hey guys,
> Yep, planned on using ballscrews for x / y. They're
> just too sloppy for planning on making holes that do
> not look like eggs. Fine for manual straight lines
> but I realize it'd be a bear on cnc.
>
> This is one of those things I wish I had a cnc mill to
> make the conversion.... lol ;-) and also thanks for
> the pics on your site Bubba.... I've got to go get my
> 3 ph hooked to my mill/drill today and take
> measurements for acceptable ballscrews so I can start
> watching ebay.
>
> Darren Lucke
>
> --- cncgramps <cncgramps@y...> wrote:
>
> >
> > Hi.
> >
> > Did you plan on using ball screws for the X and Y?
> > If not then using the micro feed for the Z would be
> > as good as the
> > acme screws that comes with the XY right now.
> > I made brackets and used ball screws for all axis.
> > I also used
> > angular contact bearings all the way though.
> > Depends on what you are doing, Just adding motors
> > to the mill/drill
> > the way it is might be fine.
> >
> > Gary
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, Darren Lucke
> >
> > <oneluckeboy@y...> wrote:
> > >
> > >
> > >
> > > --- cncgramps <cncgramps@y...> wrote:
> > > Yeah, looked at that.... the micro-feed is
> > probably
> > > the one with the least slop in it tho... :-) It's
> > got
> > > a return spring on it taking up any slack but I
> > > haven't opened it up yet either to look at it.
> > > Darren Lucke
> > >
> > >
> > >
> > > >
> > > > I would not recommend running the Z off of the
> > micro
> > > > feed.
> > > > It is well worth hooking a ball screw to the
> > quill.
> > > > I think the micro feed would have to much slop
> > in
> > > > it to do a good
> > > > job.
> > > > I used a ball screw for my Z and it works
> > great.
> > > > I did this on a JET mill/drill which is about
> > the
> > > > same as all the
> > > > rest.
> > > >
> > > > Gary
> > > >
> > >
> > > __________________________________________________
> > > Do You Yahoo!?
> > > Tired of spam? Yahoo! Mail has the best spam
> > protection around
> > > http://mail.yahoo.com
> > >
> >
> >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES:
> > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe:
> > CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe:
> > CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > wanliker@a..., timg@k...
> > Moderator: pentam@c... indigo_red@q...
> > davemucha@j... [Moderators]
> > URL to this group:
> > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru
> > Google.com to reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I
> > consider this to be a sister site to the CCED group,
> > as many of the same members are there, for OT
> > subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC
> > DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT
> > ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links
> >
> >
> > CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> >
> >
> >
> >
> >
>
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com
>

Discussion Thread

Owen 2006-01-19 15:16:04 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase Jon Elson 2006-01-19 18:50:00 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase Owen 2006-01-19 20:30:03 UTC RE: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase joe camel 2006-01-19 21:38:11 UTC Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D ED MAISEY 2006-01-20 01:40:39 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Roy J. Tellason 2006-01-20 08:07:01 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase Jon Elson 2006-01-20 09:23:48 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase Jon Elson 2006-01-20 09:27:33 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase cnc002@a... 2006-01-20 09:33:19 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase cnc002@a... 2006-01-20 09:56:05 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase Roy J. Tellason 2006-01-20 10:06:26 UTC Re: [CAD_CAM_EDM_DRO] replacing servo motor help >signal phase Owen 2006-01-20 16:37:39 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Art Eckstein 2006-01-20 18:12:17 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-20 19:00:56 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-20 19:40:14 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D bobmcknight@c... 2006-01-20 20:58:04 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-20 21:01:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 03:51:36 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Art Eckstein 2006-01-21 07:04:40 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-21 08:24:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 10:33:50 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Jon Elson 2006-01-21 12:03:07 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 12:50:38 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Owen 2006-01-21 13:29:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Owen 2006-01-21 13:32:29 UTC Re: [CAD_CAM_EDM_DRO] Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D turyga1963 2006-01-21 17:30:25 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-21 19:15:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 19:50:13 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 20:01:15 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 20:13:09 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Owen 2006-01-21 20:19:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-21 20:21:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-21 20:23:10 UTC RE: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 22:32:42 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D cncgramps 2006-01-21 23:06:21 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Darren Lucke 2006-01-21 23:12:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Dan Mauch 2006-01-22 08:35:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D joe camel 2006-02-17 01:46:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D joe camel 2006-05-11 14:40:17 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Alan Marconett 2006-05-11 14:55:49 UTC RE: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Abby Katt 2006-05-11 16:18:56 UTC Conversion Update: 2/3 - also - Rong Fu 31/25 CNC Conversion Help? R Rogers 2006-05-11 16:23:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D R Rogers 2006-05-11 16:31:43 UTC Re: [CAD_CAM_EDM_DRO] Conversion Update: 2/3 - also - Rong Fu 31/25 CNC Conversion Help? Dan Mauch 2006-05-11 21:05:14 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D ballendo 2006-05-11 23:49:45 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D ballendo 2006-05-11 23:57:27 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Polaraligned 2006-05-12 03:58:38 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D R Rogers 2006-05-12 06:14:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D ballendo 2006-05-12 06:37:28 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D R Rogers 2006-05-12 07:04:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D R Rogers 2006-05-12 07:11:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D ballendo 2006-05-12 08:18:53 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D Polaraligned 2006-05-12 09:16:21 UTC Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D R Rogers 2006-05-12 10:04:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Rong Fu 31 CNC Conversion Kit / Instructions / Help? :D