Re: [CAD_CAM_EDM_DRO] Vacuum Table
Posted by
Rich D.
on 2001-06-22 20:02:34 UTC
Tim, Bill,
I just got a flyer from MECI (Mendelson's in Dayton, OH 800-344-4465)
with a sale on:
"High power vacuum motor Assy's, 120VAC, 12A, 5-3/4" dia x
5-1/4" long Mfg. Mossler, designed to used in vacuum tube message
systems" p/n 420-0579 $24.95 These are bare motor units
with the vacuum unit attached directly like a shop vac.
RichD
Tim Goldstein wrote:
I just got a flyer from MECI (Mendelson's in Dayton, OH 800-344-4465)
with a sale on:
"High power vacuum motor Assy's, 120VAC, 12A, 5-3/4" dia x
5-1/4" long Mfg. Mossler, designed to used in vacuum tube message
systems" p/n 420-0579 $24.95 These are bare motor units
with the vacuum unit attached directly like a shop vac.
RichD
Tim Goldstein wrote:
>
> I would second the high volume low vacuum approach. I don't think I would
> use a shop-vac, but would instead invest in a couple HP dust collector. They
> are made to run continuous duty and will pull a decent vacuum. The problem
> with the lab type pumps is that they can not move much of a volume so even a
> little air leak will over whelm them.
>
> Tim
> [Denver, CO]
>
> > -----Original Message-----
> > Anyone out there ever built a vacuum table for a cnc router? I am
> > in the process of building a new larger router and would like to add
> > a vacuum part hold down to it. I picked up a couple of vacuum pumps
> > at the NC State University surplus today although I am not sure if they
> > will work for it yet. They are nice units direct drive high vacuum lab
> > units. What I need to know is what size and number of holes would
> > I drill in a 4' X 4' table? I will probably add some valves to section
> > the table off, possibly go back and get another pump and section it
> > into thirds, one pump for each section. Use only the sections I need
> > to, depending on the size fo the work. I was thinking of using an acrylic
> > sheet maybe 3/4" thick for the table. Will it require a large O-Ring
> > around the edge or will just the holes be sufficent? Any tips would be
> > appreciated.
> >
> > Thanks
> > Bill
> >
> >
Discussion Thread
William Scalione
2001-06-22 17:38:47 UTC
Vacuum Table
jesse
2001-06-22 17:58:21 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
Tim Goldstein
2001-06-22 18:35:14 UTC
RE: [CAD_CAM_EDM_DRO] Vacuum Table
Bob Campbell
2001-06-22 18:45:53 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
dougrasmussen@c...
2001-06-22 19:45:22 UTC
Re: Vacuum Table
Rich D.
2001-06-22 20:02:34 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
jesse
2001-06-23 09:59:17 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
William Scalione
2001-06-23 11:20:59 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
Jon Elson
2001-06-23 15:21:15 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
ballendo@y...
2001-06-23 16:45:53 UTC
Re: Vacuum Table
Doug Harrison
2001-06-23 17:36:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
jesse
2001-06-23 19:51:20 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
jesse
2001-06-23 19:51:42 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
Scott M. Thomas
2001-06-23 21:20:05 UTC
RE: [CAD_CAM_EDM_DRO] Vacuum Table
William Scalione
2001-06-23 21:23:54 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
Sven Peter, TAD S.A.
2001-06-23 21:34:54 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
Tim Goldstein
2001-06-23 21:41:00 UTC
RE: [CAD_CAM_EDM_DRO] Vacuum Table
Jon Elson
2001-06-23 22:57:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
jesse
2001-06-24 05:30:06 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
info.host@b...
2001-06-24 06:34:33 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
Sven Peter, TAD S.A.
2001-06-24 06:46:03 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
cadcamcenter@y...
2001-06-24 06:58:53 UTC
Vacuum Table
Sven Peter, TAD S.A.
2001-06-24 07:08:51 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
info.host@b...
2001-06-24 08:13:37 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
JanRwl@A...
2001-06-24 15:55:32 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
cadcamcenter@y...
2001-06-24 21:38:34 UTC
Re: Vacuum Table
Sven Peter, TAD S.A.
2001-06-24 22:21:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
Sven Peter, TAD S.A.
2001-06-24 22:24:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
cadcamcenter@y...
2001-06-25 02:41:45 UTC
Re: Vacuum Table
Sven Peter, TAD S.A.
2001-06-25 05:26:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
Kevin P. Martin
2001-06-25 08:16:21 UTC
RE: [CAD_CAM_EDM_DRO] Vacuum Table
Bob Campbell
2001-06-25 09:03:04 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
brian
2001-06-25 09:37:32 UTC
Re: [CAD_CAM_EDM_DRO] Vacuum Table
ballendo@y...
2001-06-26 04:07:23 UTC
Re: Vacuum Table
ballendo@y...
2001-06-26 04:21:01 UTC
Re: Vacuum Table
ballendo@y...
2001-06-26 04:44:19 UTC
mdf for machines was Re: Vacuum Table
ballendo@y...
2001-06-26 04:49:46 UTC
Re: Vacuum Table
Carol & Jerry Jankura
2001-06-26 04:51:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Vacuum Table
ballendo@y...
2001-06-26 05:13:42 UTC
Machine materials was Re: Vacuum Table
ballendo@y...
2001-06-26 05:28:15 UTC
Re: Vacuum Table
Paul
2001-06-26 12:08:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
ballendo@y...
2001-06-26 17:51:10 UTC
Re: Vacuum Table
Sven Peter, TAD S.A.
2001-06-26 21:42:10 UTC
Re: [CAD_CAM_EDM_DRO] Machine materials was Re: Vacuum Table
cncnovice
2007-02-12 06:42:26 UTC
Vacuum Table
turbulatordude
2007-02-12 17:30:18 UTC
Re: Vacuum Table
Sebastien Bailard
2007-02-14 23:26:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
JanRwl@A...
2007-02-14 23:37:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
H & J Johnson
2007-02-15 06:12:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
turbulatordude
2007-02-15 07:21:11 UTC
Re: Vacuum Table
Chris Brown
2007-02-15 07:45:48 UTC
Re: Vacuum Table
H & J Johnson
2007-02-15 08:19:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
David G. LeVine
2007-02-15 10:34:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
H & J Johnson
2007-02-15 11:49:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Vacuum Table
roboticscnc
2007-02-16 03:45:02 UTC
Re: Vacuum Table