CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-(

Posted by RC
on 2002-05-06 16:13:00 UTC
Can you tell us more about the zenor diode, how it is connected, a good
souce for them, and the specs?

Thanks,
RC
----- Original Message -----
From: Nicolas Benezan <bene@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, May 06, 2002 2:42 AM
Subject: Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-(


> Peter wrote:
> > Sean, you were very gracious (in defeat) to share your experience and
> > hopefully save others from the same misadventure.
>
> One more hint I have to add:
>
> NEVER try to run a Gecko from a regulated power supply. A friend of mine
> did and fried his Gecko immediately at the first power up. I think, what
> happened was that the motor began to oscillate due to the wrong
> gain/damp adjustment. A regulated power supply can source enough current
> for the gecko while holding the voltage exactly constant. But only few
> of them are designed to _sink_ current, when the motor is acting as
> generator which it does repeatedly when it is oscillating. So the
> voltage rises in an uncontrolled way overloading the power transistors
> of the Gecko. We replaced the FETS but with no luck. Seems that the 5V
> regulator was fried, too.
>
> So always add al _large_ capacitor to the DC supply. I even add a
> seperate "energy absorber" (large Zener diode or
> Zener-transistor-resistor combination) to my setups because I don't
> trust the capacitor alone.
>
> Ciao
> Bene
>
> --
> !!! Achtung, neue Adresse !!!
> Benezan Electronics, Maria-Merian-Str. 20a, 70736 Fellbach, Germany
> Kundenspezifische Elektronikentwicklung, Sondermaschinenbau
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

audiomaker2000 2002-05-03 15:04:15 UTC 2 Fried G210's in a single day :-( audiomaker2000 2002-05-03 18:19:36 UTC Re: 2 Fried G210's in a single day :-( art 2002-05-03 18:28:26 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( Alan Marconett KM6VV 2002-05-03 20:05:29 UTC Re: [CAD_CAM_EDM_DRO] 2 Fried G210's in a single day :-( Peter 2002-05-03 20:48:05 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( dave_ace_me 2002-05-03 21:00:32 UTC fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( Carol & Jerry Jankura 2002-05-03 22:21:26 UTC RE: [CAD_CAM_EDM_DRO] fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( Jon Elson 2002-05-03 22:45:14 UTC Re: [CAD_CAM_EDM_DRO] 2 Fried G210's in a single day :-( studleylee 2002-05-03 23:35:31 UTC fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( studleylee 2002-05-03 23:39:42 UTC fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( keongsan 2002-05-04 00:46:54 UTC Re: 2 Fried G210's in a single day :-( keongsan 2002-05-04 00:59:12 UTC Re: 2 Fried G210's in a single day :-( Dan Mauch 2002-05-04 08:51:00 UTC RE: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( audiomaker2000 2002-05-04 09:35:04 UTC Re: 2 Fried G210's in a single day :-( audiomaker2000 2002-05-04 09:38:04 UTC Re: 2 Fried G210's in a single day :-( Alan Marconett KM6VV 2002-05-04 10:11:56 UTC Re: [CAD_CAM_EDM_DRO] fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( Alan Marconett KM6VV 2002-05-04 10:33:17 UTC Re: [CAD_CAM_EDM_DRO] fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( Alan Marconett KM6VV 2002-05-04 11:23:46 UTC Re: [CAD_CAM_EDM_DRO] fusing Gecko leads ( was Re: 2 Fried G210's in a single day :-( Nicolas Benezan 2002-05-06 09:43:29 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( pavel59 2002-05-06 16:12:02 UTC Re: 2 Fried G210's in a single day :-( RC 2002-05-06 16:13:00 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( dave_ace_me 2002-05-06 16:43:06 UTC Re: 2 Fried G210's in a single day :-( studleylee 2002-05-06 17:16:48 UTC Re: 2 Fried G210's in a single day :-( Tim Goldstein 2002-05-06 18:33:11 UTC RE: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( pavel59 2002-05-07 01:21:01 UTC Re: 2 Fried G210's in a single day :-( dave_ace_me 2002-05-07 04:17:42 UTC good ideas ( was Re: 2 Fried G210's in a single day :-( dave_ace_me 2002-05-07 04:30:55 UTC more data ( Re: 2 Fried G210's in a single day :-( pavel59 2002-05-07 05:23:20 UTC more data ( Re: 2 Fried G210's in a single day :-( turbulatordude 2002-05-07 05:43:18 UTC more data ( Re: 2 Fried G210's in a single day :-( Nicolas Benezan 2002-05-07 06:07:33 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( Tim Goldstein 2002-05-07 09:15:04 UTC Re: [CAD_CAM_EDM_DRO] more data ( Re: 2 Fried G210's in a single day :-( keongsan 2002-05-07 19:41:35 UTC Re: 2 Fried G210's in a single day :-( keongsan 2002-05-07 19:55:06 UTC more data ( Re: 2 Fried G210's in a single day :-( mariss92705 2002-05-07 19:59:40 UTC more data ( Re: 2 Fried G210's in a single day :-( turbulatordude 2002-05-08 04:07:15 UTC more data ( Re: 2 Fried G210's in a single day :-( beer@s... 2002-05-08 10:55:35 UTC Re: Re: 2 Fried G210's in a single day :-( mariss92705 2002-05-08 12:48:39 UTC Re: 2 Fried G210's in a single day :-( JanRwl@A... 2002-05-08 16:40:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: 2 Fried G210's in a single day :-( Jon Elson 2002-05-08 22:13:06 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-( mariss92705 2002-05-09 07:05:26 UTC Re: 2 Fried G210's in a single day :-( Jon Elson 2002-05-09 22:50:27 UTC Re: [CAD_CAM_EDM_DRO] Re: 2 Fried G210's in a single day :-(