CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option

on 2005-01-31 13:00:24 UTC
Differential encoders have no effect on CPR. It is just a method of putting a signal on wires.

By using 2 wires for the signal you can assume that any signal on both lines is noise which makes filtering quite easy.


-----Original Message-----
From: braidmeister <braidmeister@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Mon Jan 31 11:39:15 2005
Subject: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option



3 Questions still floating out there:

1. Is there any reason why I would need an Index feature on the
encoder for the Bridgeport? Doesn't this have something to do with
threading/tapping? (I will be running Mach2...is this a moot point?)

2. If running sheilded lines less than 8 feet long, is there really
justification to go to a differential encoder? It seems to me that in
the case of US Digital, that it would be a PITA to convert a shaft-
type encoder to my motors...The ideal setup would be a hole-thru
design with a 5/8" encoder.

3. If I did select a differential encoder, is there any bearing on
the CPR rating? I mean, would there be a difference between a 1000
CPR non-diff and a 1000 CPR differential?

-Brady


--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
> Polaraligned wrote:
>
> >I don't know about the one you spec'd out. I did not look
> >yours up. Diff encoders have an inverted output also for each
channel.
> >
> >Check this out.
> >
> >http://www.rutex.com/home/index
> >
> >Go to bottom of page and download whole pdf document.
> >
> >It is a great source of info on setting up a servo system
> >using rutex hardware. It gives lots of encoder interfacing
> >info. Using diff encoders may save a headache. So if the
> >cost is small, which it should be, why not use them?
> >
> >Scott
> >
> >
> I think they changed their website around recently - there's no PDF
> linked at the bottom of the page :)
> You might want to put in the name of the file you were suggesting,
or a
> direct link to it.
>
> - Steve





Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links










-----------------------------------------
The information contained in this transmission may contain privileged and confidential information and is intended only for the use of the person(s) named above. If you are not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, any review, dissemination, distribution or duplication of this communication is strictly prohibited. If you are not the intended recipient, please contact the sender immediately by reply e-mail and destroy all copies of the original message. Please note that we do not accept account orders and/or instructions by e-mail, and therefore will not be responsible for carrying out such orders and/or instructions.
If you, as the intended recipient of this message, the purpose of which is to inform and update our clients, prospects and consultants of developments relating to our services and products, would not like to receive further e-mail correspondence from the sender, please "reply" to the sender indicating your wishes. In the U.S.: 1345 Avenue of the Americas, New York, NY 10105.

Discussion Thread

braidmeister 2005-01-30 18:38:54 UTC Encoder Indexer Option Stephen Wille Padnos 2005-01-30 18:53:32 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option R Rogers 2005-01-30 18:53:34 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option R Rogers 2005-01-30 19:08:51 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option Stephen Wille Padnos 2005-01-30 19:15:01 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option braidmeister 2005-01-30 19:15:59 UTC Re: Encoder Indexer Option R Rogers 2005-01-30 19:20:56 UTC Automobile starter motor as servo?? R Rogers 2005-01-30 19:27:46 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option Luke1027 2005-01-30 19:29:36 UTC Re: [CAD_CAM_EDM_DRO] Automobile starter motor as servo?? R Rogers 2005-01-30 19:30:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option Luke1027 2005-01-30 19:33:53 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option Stephen Wille Padnos 2005-01-30 19:50:11 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option R Rogers 2005-01-30 19:59:09 UTC Re: [CAD_CAM_EDM_DRO] Encoder Indexer Option turbulatordude 2005-01-30 20:20:01 UTC Re: Encoder Indexer Option --- opening up steppers.......and modfying shafts... Scott Ellis 2005-01-30 21:33:44 UTC Re: [CAD_CAM_EDM_DRO] Automobile starter motor as servo?? braidmeister 2005-01-30 21:37:44 UTC Re: Encoder Indexer Option --- opening up steppers.......and modfying shafts... Jon Elson 2005-01-30 21:48:20 UTC Re: [CAD_CAM_EDM_DRO] Automobile starter motor as servo?? Marv Frankel 2005-01-31 03:21:34 UTC Re: Encoder Indexer Option --- opening up steppers.......and modfying shafts... Andy Wander 2005-01-31 04:43:25 UTC RE: [CAD_CAM_EDM_DRO] Encoder Indexer Option Polaraligned 2005-01-31 04:49:52 UTC Re: Encoder Indexer Option turbulatordude 2005-01-31 06:52:59 UTC Re: Encoder Indexer Option --- opening up steppers.......and modfying shafts... R Rogers 2005-01-31 07:25:09 UTC Re: [CAD_CAM_EDM_DRO] Automobile starter motor as servo?? braidmeister 2005-01-31 07:30:19 UTC Re: Encoder Indexer Option R Rogers 2005-01-31 07:32:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option --- opening up steppers.......and modfying shafts... Andy Wander 2005-01-31 07:47:49 UTC RE: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option --- opening up steppers.......and modfying shafts... Polaraligned 2005-01-31 08:23:26 UTC Re: Encoder Indexer Option Stephen Wille Padnos 2005-01-31 08:30:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option Stephen Wille Padnos 2005-01-31 08:31:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option braidmeister 2005-01-31 08:32:51 UTC Re: Encoder Indexer Option braidmeister 2005-01-31 08:42:23 UTC Re: Encoder Indexer Option Stephen Wille Padnos 2005-01-31 08:49:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option John Rouche 2005-01-31 08:51:15 UTC Re: Encoder Indexer Option braidmeister 2005-01-31 09:01:09 UTC Re: Encoder Indexer Option Polaraligned 2005-01-31 11:04:09 UTC Re: Encoder Indexer Option braidmeister 2005-01-31 11:16:08 UTC Re: Encoder Indexer Option Polaraligned 2005-01-31 11:36:30 UTC Re: Encoder Indexer Option braidmeister 2005-01-31 11:45:53 UTC Re: Encoder Indexer Option Stephen Wille Padnos 2005-01-31 12:44:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option Terrenoire, Adrien L 2005-01-31 13:00:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option David A. Frantz 2005-01-31 14:10:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder Indexer Option braidmeister 2005-01-31 14:43:34 UTC Re: Encoder Indexer Option cnc_4_me 2005-01-31 17:33:36 UTC Re: Encoder Indexer Option braidmeister 2005-01-31 18:07:28 UTC Re: Encoder Indexer Option cnc_4_me 2005-01-31 19:10:35 UTC Re: Encoder Indexer Option Stephan Kotze 2005-02-01 00:36:14 UTC Re: Automobile starter motor as servo?? R Rogers 2005-02-01 06:13:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Automobile starter motor as servo?? Jon Elson 2005-02-01 09:59:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Automobile starter motor as servo?? Brian 2005-02-01 16:40:19 UTC Re: [CAD_CAM_EDM_DRO] Automobile starter motor as servo??