CAD CAM EDM DRO - Yahoo Group Archive

Re: Moog makes it home

on 2003-02-04 13:52:59 UTC
> If you have the table plate w/ coolant trough, it might be a good
idea to
> keep it around.

I have one, though it doesn't look like the one in the manual. I
expect it was made by the PO. there's a sheet metal tray that fits
around the table with the t-slots. It could be a sub plate, or it
could be the table itself. Most likely the latter.

Getting back to mounting the x ballscrew, it looks like the table is
small compared to the saddle, and I suspect it would be difficult to
get even close to that long travel by mounting the screw to the
table, correct? (I still think it's incredible that you were able to
nearly double the x axis travel) So using a cog belt and tucking the
servo underneath clearly makes sense seen in that light. Wouldn't it
make sense to just eliminate the side extensions on the saddle as
well?


> I didn't use it because my servo mount would have protruded too
> far if I had mounted it on the extension casting.

Agreed. That extension casting has got to go. I'm looking at a photo
showing the removal of the y actuator, and the man is removing allen
screws from that support which is sticking out maybe a couple inches
or so from the face of the knee with the saddle about 1/2" in from
that face. What I was thinking was to just whack off that 2" and
drill that piece for the nut support, then use a plate for the
bearing support and servo mount, tucking the servo under the saddle
either to the right or the left, wherever the x servo isn't. Who
knows, there could even be room enough to put it inside the knee,
but I doubt my servos are small enough for that.
>
> I think Ray Henry had some thoughts about EMC'ing a Moog at some
point.

Yes he did. I have that post saved in a file on my desktop and will
review it a few times as I begin disassembly. Maybe next week it
will warm up enough to work on it a bit.

Jim

Discussion Thread

blown_mgb_v8 <jblackwood5@i... 2003-01-31 11:46:23 UTC Moog makes it home jmkasunich <jmkasunich@y... 2003-01-31 14:23:24 UTC Re: Moog makes it home Bill Higdon 2003-01-31 19:48:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-02 07:13:25 UTC Re: Moog makes it home Keith Rumley 2003-02-03 08:54:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-03 09:57:15 UTC Re: Moog makes it home Bill Higdon 2003-02-03 12:53:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home Keith Rumley 2003-02-03 13:50:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-03 19:11:07 UTC Re: Moog makes it home Keith Rumley 2003-02-03 20:45:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-04 13:52:59 UTC Re: Moog makes it home Keith Rumley 2003-02-04 20:34:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-05 07:30:36 UTC Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-17 21:45:41 UTC Re: Moog makes it home Andrew Mawson <andrew@m... 2003-02-18 08:40:49 UTC Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-18 17:57:09 UTC Re: Moog makes it home blown_mgb_v8 <jblackwood5@i... 2003-02-22 18:24:33 UTC Re: Moog ways are good (makes it home) Andrew Mawson <andrew@m... 2003-02-23 00:43:33 UTC Re: Moog ways are good (makes it home) Jerry Biehler 2003-02-23 06:13:47 UTC Stepper wiring Tony Jeffree 2003-02-23 06:17:04 UTC Re: [CAD_CAM_EDM_DRO] Stepper wiring ajv2803959 <antonio-ximenez@t... 2003-02-24 07:42:01 UTC Re: Stepper wiring blown_mgb_v8 <jblackwood5@i... 2003-02-25 15:04:49 UTC Re: Moog ways are good (makes it home) blown_mgb_v8 <jblackwood5@i... 2003-02-27 17:32:28 UTC Re: Moog: Too much clutter blown_mgb_v8 2003-03-09 16:29:17 UTC Re: Moog: Servo for Z? Jon Elson 2003-03-09 21:48:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z? blown_mgb_v8 2003-03-10 17:01:58 UTC Re: Moog: Servo for Z? Jon Elson 2003-03-10 23:13:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z? blown_mgb_v8 2003-03-12 16:53:01 UTC Re: Moog: Servo for Z? Jon Elson 2003-03-12 22:31:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z? blown_mgb_v8 2003-03-15 20:52:59 UTC Re: Moog: Servo for Z? blown_mgb_v8 2003-03-27 20:04:01 UTC Re: Moog: Where are all the air valves? Andrew Mawson 2003-03-28 01:27:47 UTC Re: Moog: Where are all the air valves? blownmgb_v8 2005-09-03 15:30:17 UTC Re: Moog: update