Re: Moog: Servo for Z?
Posted by
blown_mgb_v8
on 2003-03-12 16:53:01 UTC
I've been looking at ballscrews and trying to figure out how to
calculate torque from linear pressure. Example, a 5/8" dia ballscrew
with .200 pitch, if I'm calculating for 200lbs of downforce how do I
get from there to the torque figure needed to drive it?
there's
today and set it in the housing, and the left side really looks like
a good place for the screw. It can get in close and the nut would be
really easy to mount, but the end mount for the screw would be more
trouble. However it would be well protected by the housing itself.
At the moment I'm working on installing a worm and pinion so I can
use the head tilt. That part was left out so I'm trying to adapt
parts from an old gear reducer. Then I'll clean up the cuts I made
with the grinder to get everything flat and square. That should give
me some good mounting points for the motor and screw end bearing.
Jim
calculate torque from linear pressure. Example, a 5/8" dia ballscrew
with .200 pitch, if I'm calculating for 200lbs of downforce how do I
get from there to the torque figure needed to drive it?
there's
> a link to "My Z-axis drive" with a set of pictures from differenthousing
> angles. This drives the
> quill by the hole where the stop ring goes, and attaches to the
> by the holes thatThat looks real workable. Nice guards too. I cut down the quill yoke
> the stop rod normally sits in.
>
> Jon
today and set it in the housing, and the left side really looks like
a good place for the screw. It can get in close and the nut would be
really easy to mount, but the end mount for the screw would be more
trouble. However it would be well protected by the housing itself.
At the moment I'm working on installing a worm and pinion so I can
use the head tilt. That part was left out so I'm trying to adapt
parts from an old gear reducer. Then I'll clean up the cuts I made
with the grinder to get everything flat and square. That should give
me some good mounting points for the motor and screw end bearing.
Jim
Discussion Thread
blown_mgb_v8 <jblackwood5@i...
2003-01-31 11:46:23 UTC
Moog makes it home
jmkasunich <jmkasunich@y...
2003-01-31 14:23:24 UTC
Re: Moog makes it home
Bill Higdon
2003-01-31 19:48:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-02 07:13:25 UTC
Re: Moog makes it home
Keith Rumley
2003-02-03 08:54:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-03 09:57:15 UTC
Re: Moog makes it home
Bill Higdon
2003-02-03 12:53:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
Keith Rumley
2003-02-03 13:50:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-03 19:11:07 UTC
Re: Moog makes it home
Keith Rumley
2003-02-03 20:45:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-04 13:52:59 UTC
Re: Moog makes it home
Keith Rumley
2003-02-04 20:34:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-05 07:30:36 UTC
Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-17 21:45:41 UTC
Re: Moog makes it home
Andrew Mawson <andrew@m...
2003-02-18 08:40:49 UTC
Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-18 17:57:09 UTC
Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-22 18:24:33 UTC
Re: Moog ways are good (makes it home)
Andrew Mawson <andrew@m...
2003-02-23 00:43:33 UTC
Re: Moog ways are good (makes it home)
Jerry Biehler
2003-02-23 06:13:47 UTC
Stepper wiring
Tony Jeffree
2003-02-23 06:17:04 UTC
Re: [CAD_CAM_EDM_DRO] Stepper wiring
ajv2803959 <antonio-ximenez@t...
2003-02-24 07:42:01 UTC
Re: Stepper wiring
blown_mgb_v8 <jblackwood5@i...
2003-02-25 15:04:49 UTC
Re: Moog ways are good (makes it home)
blown_mgb_v8 <jblackwood5@i...
2003-02-27 17:32:28 UTC
Re: Moog: Too much clutter
blown_mgb_v8
2003-03-09 16:29:17 UTC
Re: Moog: Servo for Z?
Jon Elson
2003-03-09 21:48:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-10 17:01:58 UTC
Re: Moog: Servo for Z?
Jon Elson
2003-03-10 23:13:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-12 16:53:01 UTC
Re: Moog: Servo for Z?
Jon Elson
2003-03-12 22:31:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-15 20:52:59 UTC
Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-27 20:04:01 UTC
Re: Moog: Where are all the air valves?
Andrew Mawson
2003-03-28 01:27:47 UTC
Re: Moog: Where are all the air valves?
blownmgb_v8
2005-09-03 15:30:17 UTC
Re: Moog: update