Re: Moog makes it home
Posted by
Andrew Mawson <andrew@m...
on 2003-02-18 08:40:49 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "blown_mgb_v8
<jblackwood5@i...>" <jblackwood5@i...> wrote:
special Moog tooling, and also a pc parallel port to vast number of
air valves interface to drive a Moog by emulating its paper tape !
Andrew Mawson,
Bromley,
Kent,
UK
<jblackwood5@i...>" <jblackwood5@i...> wrote:
> Just a quick update, I managed to unload the machine from thetruck
> trailer today, and it went pretty smoothly. Among other things, I
> angled the trailer down in the back, attached the ramps, used the
> winch to pull the pallet off onto the ramps, and then used the
> to pull the ramps out from under the pallet. Took it real slow andbuilding
> cautious and had it unloaded in about 3 hours. I hope to begin
> disassembly tomorrow. I'll leave the mill on the pallet until the
> new shop goes up, then plan to drag the pallet into the new
> and lift the mill off with an overhead hoist or other method,If you're ever this side of the pond, I've still got some of the
> depending on what gets finished when. I'm really looking forward to
> having a look at the pieces.
>
> Jim
special Moog tooling, and also a pc parallel port to vast number of
air valves interface to drive a Moog by emulating its paper tape !
Andrew Mawson,
Bromley,
Kent,
UK
Discussion Thread
blown_mgb_v8 <jblackwood5@i...
2003-01-31 11:46:23 UTC
Moog makes it home
jmkasunich <jmkasunich@y...
2003-01-31 14:23:24 UTC
Re: Moog makes it home
Bill Higdon
2003-01-31 19:48:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-02 07:13:25 UTC
Re: Moog makes it home
Keith Rumley
2003-02-03 08:54:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-03 09:57:15 UTC
Re: Moog makes it home
Bill Higdon
2003-02-03 12:53:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
Keith Rumley
2003-02-03 13:50:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-03 19:11:07 UTC
Re: Moog makes it home
Keith Rumley
2003-02-03 20:45:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-04 13:52:59 UTC
Re: Moog makes it home
Keith Rumley
2003-02-04 20:34:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-05 07:30:36 UTC
Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-17 21:45:41 UTC
Re: Moog makes it home
Andrew Mawson <andrew@m...
2003-02-18 08:40:49 UTC
Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-18 17:57:09 UTC
Re: Moog makes it home
blown_mgb_v8 <jblackwood5@i...
2003-02-22 18:24:33 UTC
Re: Moog ways are good (makes it home)
Andrew Mawson <andrew@m...
2003-02-23 00:43:33 UTC
Re: Moog ways are good (makes it home)
Jerry Biehler
2003-02-23 06:13:47 UTC
Stepper wiring
Tony Jeffree
2003-02-23 06:17:04 UTC
Re: [CAD_CAM_EDM_DRO] Stepper wiring
ajv2803959 <antonio-ximenez@t...
2003-02-24 07:42:01 UTC
Re: Stepper wiring
blown_mgb_v8 <jblackwood5@i...
2003-02-25 15:04:49 UTC
Re: Moog ways are good (makes it home)
blown_mgb_v8 <jblackwood5@i...
2003-02-27 17:32:28 UTC
Re: Moog: Too much clutter
blown_mgb_v8
2003-03-09 16:29:17 UTC
Re: Moog: Servo for Z?
Jon Elson
2003-03-09 21:48:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-10 17:01:58 UTC
Re: Moog: Servo for Z?
Jon Elson
2003-03-10 23:13:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-12 16:53:01 UTC
Re: Moog: Servo for Z?
Jon Elson
2003-03-12 22:31:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-15 20:52:59 UTC
Re: Moog: Servo for Z?
blown_mgb_v8
2003-03-27 20:04:01 UTC
Re: Moog: Where are all the air valves?
Andrew Mawson
2003-03-28 01:27:47 UTC
Re: Moog: Where are all the air valves?
blownmgb_v8
2005-09-03 15:30:17 UTC
Re: Moog: update