CAD CAM EDM DRO - Yahoo Group Archive

Re: machine ways

Posted by doug98105
on 2002-01-05 07:57:52 UTC
Ballendo,

What about Moglice? Does that fit into one of the 4 groups of
engineeered plastics or is it a totally different animal?

I don't have first hand experience with the product, but I believe
it's one of the easier way-lining materials to work with. Since it's
a pourable mixture it has advantages over other plastics which might
only be available in sheet, strip, and rod forms.

Doug

--- In CAD_CAM_EDM_DRO@y..., "ballendo" <ballendo@y...> wrote:
> Ted,
>
> There are 4 "engineered" plastics commonly used industrially (of
> course, there are thousands; but these 4 groups are prevalent in
> machinery apps)
>
> As the grandaddy, Nylon also needs to be mentioned, as it is
> ubiquitous(means everywhere!). Often it is used in a "filled" way
> (with oil or grease) for bearings and sliding surfaces of many
types.
> Like UHMW, it "grows" and "shrinks".
>
> 1)UHMW PE- (Ultra High Molecular Weight PolyEthylene) Like super-
> duper milk jug plastic. Used a lot in conveyer systems and food
> processing, as it can be sterilised easily. Very tough, slippery,
but
> has a fair amount of movement(size change) due to temperature and
> humidity
>
> 2)PTFE- (PolyTetraFluoroEthylene) also called teflon, VERY soft,
when
> used for linear bearings it is backed up with a harder material and
> used in very thin layers. The slippery-est (lowest friction co-
> efficient) stuff we have so far in commercial quantities.
>
> 3)Acetal- One trade name is Delrin. It is hard and machines
> extremely well.
>
> And finally, the one you were probably referring to:
>
> 4)Turcite- which is a combination of TFE (teflon) and acetal
(delrin).
> It is used as a lining of ways by many CNC and machine mfrs. And
yes,
> it needs GOOD lubrication system(s) for long life. It is also used
to
> make the nuts that drive many of our smaller CNC machines, and they
> need to be properly lubed as well...
>
> http://www.polymerplastics.com/ is one good site for engineering
> plastics information
>
> Hope this helps.
>
> Ballendo
>
> --- In CAD_CAM_EDM_DRO@y..., "Ted Walls" <tiffyted@l...> wrote:
> <snip> Some modern industrial machines use quite a soft plastic
> > bearing material (can't recall
> > its name) for the bearing surfaces which if not well lubricated
> > becomes useless after a very short period.
> >

Discussion Thread

jtfrimenko 2001-12-28 05:42:59 UTC Motor vs. Servo ballendo 2001-12-28 05:55:54 UTC Re: Motor vs. Servo Les Watts 2001-12-28 06:46:23 UTC Re: [CAD_CAM_EDM_DRO] Motor vs. Servo Ian Wright 2001-12-28 07:00:12 UTC Re: [CAD_CAM_EDM_DRO] Motor vs. Servo jtfrimenko 2001-12-28 07:37:47 UTC Re: Motor vs. Servo Bill Vance 2001-12-28 08:40:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo nielsenbe@a... 2001-12-28 09:34:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Smoke 2001-12-28 10:24:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Les Watts 2001-12-28 10:39:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Jon Elson 2001-12-28 10:57:18 UTC Re: [CAD_CAM_EDM_DRO] Motor vs. Servo Jon Elson 2001-12-28 11:16:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Jon Elson 2001-12-28 11:18:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo ballendo 2001-12-28 14:22:12 UTC Re: Motor vs. Servo Bill Vance 2001-12-28 20:47:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Jon Elson 2001-12-28 23:00:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo ballendo 2001-12-29 01:47:55 UTC machine ways was Re: Motor vs. Servo ka1bbg 2001-12-29 04:44:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo jtfrimenko 2001-12-29 06:43:21 UTC Re: Motor vs. Servo Bill Vance 2001-12-29 07:36:16 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Gail & Bryan Harries 2001-12-29 07:47:09 UTC RE: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Bill Vance 2001-12-29 09:15:39 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-29 12:53:29 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-29 12:55:41 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo netcom 2001-12-29 14:34:28 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-29 16:34:52 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Sven Peter 2001-12-30 04:14:43 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Bill Vance 2001-12-30 09:12:45 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-30 16:21:22 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Sven Peter 2001-12-30 19:09:11 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo ballendo 2002-01-03 16:58:41 UTC re: machine ways ballendo 2002-01-03 17:32:06 UTC OT machine ways was Re: Motor vs. Servo Ted Walls 2002-01-04 13:50:56 UTC Re: [CAD_CAM_EDM_DRO] re: machine ways ballendo 2002-01-05 03:51:25 UTC Re: machine ways doug98105 2002-01-05 07:57:52 UTC Re: machine ways Ted Walls 2002-01-05 08:54:53 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Smoke 2002-01-05 11:14:30 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Bill Vance 2002-01-05 12:39:20 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Smoke 2002-01-05 15:04:19 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Bill Vance 2002-01-05 18:18:20 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Jon Elson 2002-01-05 22:29:49 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Jon Elson 2002-01-05 22:52:14 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways ballendo 2002-01-05 23:34:14 UTC Re: machine ways (moglice) ballendo 2002-01-06 01:40:57 UTC teflon coatings was Re: machine ways Ted Walls 2002-01-06 06:33:49 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways hllrsr@c... 2002-01-06 10:42:00 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Doug Harrison 2002-01-06 14:47:30 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways (moglice) Sven Peter 2002-01-06 17:35:42 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Jon Elson 2002-01-06 18:11:56 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways (moglice) JanRwl@A... 2002-01-07 11:15:07 UTC Re: [CAD_CAM_EDM_DRO] teflon coatings was Re: machine ways Jesse Brennan 2002-01-07 11:39:02 UTC Re: [CAD_CAM_EDM_DRO] teflon coatings was Re: machine ways