CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: machine ways

Posted by Smoke
on 2002-01-05 11:14:30 UTC
Speaking of plastics for use on ways:

I was reading the other day how PTFE is put on ubiquitous pots and pans
since it sticks to almost nothing. It is sprayed on and then baked.

This lead me to wonder 'suppose (during manufacture of course) one were get
a can of spray on PTFE and apply it to the sliding parts and bake them in
an oven'. That, combined with normal lubing should make for some pretty low
friction coefficients. An extra boon would be no extra machine work would
be required.

Sounds like a good experiment to try (with some small parts of course).

Smoke

> ubiquitous(means everywhere!).
>
> 2)PTFE- (PolyTetraFluoroEthylene) also called teflon, VERY soft, when
> used for linear bearings it is backed up with a harder material and
> used in very thin layers. The slippery-est (lowest friction co-
> efficient) stuff we have so far in commercial quantities.

> Ballendo

Discussion Thread

jtfrimenko 2001-12-28 05:42:59 UTC Motor vs. Servo ballendo 2001-12-28 05:55:54 UTC Re: Motor vs. Servo Les Watts 2001-12-28 06:46:23 UTC Re: [CAD_CAM_EDM_DRO] Motor vs. Servo Ian Wright 2001-12-28 07:00:12 UTC Re: [CAD_CAM_EDM_DRO] Motor vs. Servo jtfrimenko 2001-12-28 07:37:47 UTC Re: Motor vs. Servo Bill Vance 2001-12-28 08:40:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo nielsenbe@a... 2001-12-28 09:34:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Smoke 2001-12-28 10:24:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Les Watts 2001-12-28 10:39:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Jon Elson 2001-12-28 10:57:18 UTC Re: [CAD_CAM_EDM_DRO] Motor vs. Servo Jon Elson 2001-12-28 11:16:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Jon Elson 2001-12-28 11:18:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo ballendo 2001-12-28 14:22:12 UTC Re: Motor vs. Servo Bill Vance 2001-12-28 20:47:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo Jon Elson 2001-12-28 23:00:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo ballendo 2001-12-29 01:47:55 UTC machine ways was Re: Motor vs. Servo ka1bbg 2001-12-29 04:44:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor vs. Servo jtfrimenko 2001-12-29 06:43:21 UTC Re: Motor vs. Servo Bill Vance 2001-12-29 07:36:16 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Gail & Bryan Harries 2001-12-29 07:47:09 UTC RE: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Bill Vance 2001-12-29 09:15:39 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-29 12:53:29 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-29 12:55:41 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo netcom 2001-12-29 14:34:28 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-29 16:34:52 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Sven Peter 2001-12-30 04:14:43 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Bill Vance 2001-12-30 09:12:45 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Smoke 2001-12-30 16:21:22 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo Sven Peter 2001-12-30 19:09:11 UTC Re: [CAD_CAM_EDM_DRO] machine ways was Re: Motor vs. Servo ballendo 2002-01-03 16:58:41 UTC re: machine ways ballendo 2002-01-03 17:32:06 UTC OT machine ways was Re: Motor vs. Servo Ted Walls 2002-01-04 13:50:56 UTC Re: [CAD_CAM_EDM_DRO] re: machine ways ballendo 2002-01-05 03:51:25 UTC Re: machine ways doug98105 2002-01-05 07:57:52 UTC Re: machine ways Ted Walls 2002-01-05 08:54:53 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Smoke 2002-01-05 11:14:30 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Bill Vance 2002-01-05 12:39:20 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Smoke 2002-01-05 15:04:19 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Bill Vance 2002-01-05 18:18:20 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Jon Elson 2002-01-05 22:29:49 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Jon Elson 2002-01-05 22:52:14 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways ballendo 2002-01-05 23:34:14 UTC Re: machine ways (moglice) ballendo 2002-01-06 01:40:57 UTC teflon coatings was Re: machine ways Ted Walls 2002-01-06 06:33:49 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways hllrsr@c... 2002-01-06 10:42:00 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Doug Harrison 2002-01-06 14:47:30 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways (moglice) Sven Peter 2002-01-06 17:35:42 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways Jon Elson 2002-01-06 18:11:56 UTC Re: [CAD_CAM_EDM_DRO] Re: machine ways (moglice) JanRwl@A... 2002-01-07 11:15:07 UTC Re: [CAD_CAM_EDM_DRO] teflon coatings was Re: machine ways Jesse Brennan 2002-01-07 11:39:02 UTC Re: [CAD_CAM_EDM_DRO] teflon coatings was Re: machine ways