CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE?

Posted by Ron Thompson
on 2011-10-09 13:08:49 UTC
On 10/9/2011 3:40 PM, Mike Payson wrote:
> Rather than guessing, I made up a simple model of the part you specify, a
> block 1.625x2.5, a 1.125" hole in the center and two .1875" holes
> on opposite ends. It was not clear from your description whether the
> .1875"
> holes were through the face of the material or from the ends to the
> center.
> I made the model both ways, then processed them with Skeinforge (the
> toolpathing software the RepRap uses).
>
> The full output of each run is pasted below, is pasted below, but the gist
> of it is that these parts will cost about $5.25 each and take about 15
> minutes to run--

Mike,
I assume this is solid, yes? So if the part can be lightened, the cost
can be reduced.

I also noticed you left out some significant things in the quote. Setup,
cleanup (machine/work area), deburring, handling for shipping..just to
name a few off the top of my head.
As these are not commercial quality machines, it is reasonable to figure
life expectancy and replacement cost.

If you think this is nit picking or irrelevant, you won't be in business
long.

Also note, if anyone is using this to justify a machine build or buy,
there is a learning curve before you get good parts.

Of course, if you just want one...<GRIN>

--


Ron Thompson
On the Beautiful Florida Space Coast, right beside the Kennedy Space Center, USA

There are two kinds of posts on newsgroups.
1. This is what I have done...
2. This is what I think...
Be aware of the difference!

http://www.ourcadguy.com/

http://www.plansandprojects.com My hobby pages are here:
http://www.plansandprojects.com/My%20Machines/

Visit the castinghobby FAQ:
http://castinghobbyfaq.bareboogerhost.com/

Discussion Thread

Ron Thompson 2011-10-06 16:51:50 UTC Maybe OT, reprap build started Phil@Y... 2011-10-07 09:31:15 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Ron Thompson 2011-10-07 09:45:33 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Dan Mauch 2011-10-07 10:23:33 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Ron Thompson 2011-10-07 11:04:27 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Danny Miller 2011-10-07 12:31:25 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Kevin Martin 2011-10-07 12:39:20 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-07 17:07:18 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started wolfgang 2011-10-07 17:55:31 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-07 18:09:48 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Johnny 2011-10-08 03:49:29 UTC Re: Maybe OT, reprap build started Ron Thompson 2011-10-08 08:53:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Ron Thompson 2011-10-08 08:58:26 UTC OT New Hackerspace announcement Mike Payson 2011-10-08 16:37:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started 556RECON 2011-10-09 05:42:10 UTC REPRAP COST EFFECTIVE? turbulatordude 2011-10-09 08:15:29 UTC Re: REPRAP COST EFFECTIVE? Michael Fagan 2011-10-09 08:18:25 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Ron Thompson 2011-10-09 08:22:19 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Kevin Martin 2011-10-09 08:24:50 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Jon Elson 2011-10-09 10:16:38 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Danny Miller 2011-10-09 10:49:07 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Mike Payson 2011-10-09 12:40:25 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Ron Thompson 2011-10-09 13:08:49 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Mike Payson 2011-10-09 13:09:43 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Mike Payson 2011-10-09 13:13:43 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Mike Payson 2011-10-09 13:55:15 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started 556RECON 2011-10-09 14:17:13 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Mike Rehmus 2011-10-09 14:55:34 UTC Re: Maybe OT, reprap build started Kevin Martin 2011-10-09 15:46:14 UTC RE: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Jon Elson 2011-10-09 17:26:27 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Jon Elson 2011-10-09 17:43:06 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Mike Payson 2011-10-09 18:38:32 UTC Re: [CAD_CAM_EDM_DRO] REPRAP COST EFFECTIVE? Low Compression 2011-10-09 19:50:13 UTC Re: Maybe OT, reprap build started Danny Miller 2011-10-09 20:55:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Mike Payson 2011-10-09 20:59:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Phil@Y... 2011-10-09 21:42:02 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-09 21:56:31 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-09 22:13:10 UTC Re: Maybe OT, reprap build started Danny Miller 2011-10-09 22:34:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Phil@Y... 2011-10-09 23:11:03 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-09 23:16:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Mike Payson 2011-10-09 23:46:08 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Danny Miller 2011-10-10 01:02:15 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Kevin Martin 2011-10-10 07:23:47 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Kevin Martin 2011-10-10 07:24:21 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Kevin Martin 2011-10-10 07:31:56 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-10 10:28:24 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-10 10:31:17 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Alan 2011-10-10 10:35:37 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-10 11:21:40 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-10 11:34:26 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Alan 2011-10-10 12:08:57 UTC RE: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-10 12:09:30 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Danny Miller 2011-10-10 12:52:22 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-10 15:03:37 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-10 17:47:21 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Jon Elson 2011-10-10 19:28:41 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-10 22:01:42 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Mike Payson 2011-10-10 22:19:49 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started David G. LeVine 2011-10-11 10:32:41 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Danny Miller 2011-10-11 10:37:18 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started xoethosox 2011-10-11 14:39:15 UTC Re: Maybe OT, reprap build started Tom 2011-10-11 15:17:40 UTC Re: Maybe OT, reprap build started [moderator is not asleep} Mike Payson 2011-10-11 19:07:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Danny Miller 2011-10-12 00:20:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Maybe OT, reprap build started Phil@Y... 2011-10-12 16:25:06 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Phil@Y... 2011-10-13 08:18:35 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Les Newell 2011-10-13 08:47:41 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Lester Caine 2011-10-13 09:03:59 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Jon Elson 2011-10-13 09:52:36 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Dave Halliday 2011-10-13 16:06:11 UTC OT - open source licencing imserv1 2011-10-14 06:47:32 UTC Re: OT - open source licencing "hanermo" - CNC 6-axis Designs 2011-10-14 07:02:59 UTC Re: [CAD_CAM_EDM_DRO] Re: OT - open source licencing David G. LeVine 2011-10-16 12:10:05 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started Danny Miller 2011-10-16 12:30:31 UTC Re: [CAD_CAM_EDM_DRO] Maybe OT, reprap build started robin 2011-10-16 17:17:41 UTC Re: [CAD_CAM_EDM_DRO] Re: OT - open source licencing